Ford Crown Victoria Power Steering Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(200)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(200)

Power Steering Pump Replacement Service

How much does a Power Steering Pump Replacement cost?

On average, the cost for a Ford Crown Victoria Power Steering Pump Replacement is $281 with $99 for parts and $182 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1995 Ford Crown VictoriaV8-4.6LService typePower Steering Pump ReplacementEstimate$511.10Shop/Dealer Price$579.12 - $769.41
2010 Ford Crown VictoriaV8-4.6LService typePower Steering Pump ReplacementEstimate$593.70Shop/Dealer Price$669.33 - $887.56
1994 Ford Crown VictoriaV8-4.6LService typePower Steering Pump ReplacementEstimate$495.78Shop/Dealer Price$560.84 - $748.91
1997 Ford Crown VictoriaV8-4.6LService typePower Steering Pump ReplacementEstimate$495.78Shop/Dealer Price$560.84 - $748.91
2005 Ford Crown VictoriaV8-4.6LService typePower Steering Pump ReplacementEstimate$524.04Shop/Dealer Price$585.40 - $753.74
2004 Ford Crown VictoriaV8-4.6LService typePower Steering Pump ReplacementEstimate$524.04Shop/Dealer Price$582.60 - $748.84
1993 Ford Crown VictoriaV8-4.6LService typePower Steering Pump ReplacementEstimate$495.78Shop/Dealer Price$560.87 - $748.96
1992 Ford Crown VictoriaV8-4.6LService typePower Steering Pump ReplacementEstimate$510.38Shop/Dealer Price$575.63 - $763.83
Show example Ford Crown Victoria Power Steering Pump Replacement prices

What is the power steering pump and how does it work?

The power steering pump is a belt-driven or electric-driven hydraulic pump that generates the hydraulic pressure needed to provide power steering assist. It develops output pressures of 1,000 PSI or more. The pump output is directed to the steering gear, often a rack and pinion type unit, where the hydraulic pressure pushes on the steering rack, greatly reducing the effort it would otherwise take to turn the steering wheel.

Power Steering

When to consider replacing the power steering pump:

  • Groaning or whining noise when turning. Noise can occur if there is wear on the pump bearings or impeller vanes. A low fluid level or trapped air can also cause noises. If the pump has already been operating while dry, adding fluid may not resolve the noise and replacement of the pump might be necessary.
  • Power steering fluid leaks. Leaks can develop at pump seals, threaded connections, hoses, or on the steering rack and pinion unit. Pump seal leaks will generally require a replacement.
  • Difficult steering. Should you notice it is harder to turn the steering wheel, it might mean the power steering pump output pressure is too low, or there could be blockages in the pump or lines.
  • Damage to the pump pulley. Should the pump pulley become damaged or is loose on the pump shaft, you might detect vibration, drive belt damage, or hard steering. Either the pulley will have to be serviced or the pump assembly replaced.

How do mechanics replace the power steering pump?

  • If driven by a drive belt, the power steering pump is bolted to the engine via a bracket that allows for adjustment of the pump drive belt. Once the engine is cold, and safe to work on, the drive belt is removed.
  • If driven by an electric pump, the pump may be mounted in conjunction with the steering shaft or in conjunction with the steering rack. With either a drive belt or electric pump, removal of any dash, panel, or steering components is performed to access the pump.
  • The threaded connectors to the pump inlet and outlet are loosened and removed.
  • Any mounting bolts and brackets are removed so the pump can be removed.
  • If the old pump has failed catastrophically, or there is reason to suspect contaminants in the power steering hoses, the system is flushed.
  • The new pump is bolted on, the pressure and return hoses attached and the system is bled of all air. If pump is belt-driven, it is tightened to the manufacturer’s specification.
  • Finally, the engine is run and the car is road tested to confirm normal steering effort. If a new drive belt was installed, belt tension is measured again, and adjusted as needed, after the belt has run for a few minutes.

Is it safe to drive with a power steering pump problem?

No. If the power steering pump is operated without an adequate amount of fluid, and the pump reservoir will not hold fluid due to a large leak. The pump could seize, which would snap the serpentine belt and likely leave you stranded. If the pump turns and there is adequate fluid, but there is no power assist, it will require much greater effort to turn the steering wheel, and that presents inherent safety risks. Generally, the wisest course is to seek immediate repairs if you suspect a problem with any component in your car’s power steering system.

When replacing the power steering pump keep in mind:

  • Any belts driving the pump should be inspected and replaced as needed. The pump will only produce the required hydraulic pressure if it is driven by the belt at an adequate speed.
  • Power steering leaks from aged rubber hoses, particularly where the rubber is crimped to the steel tube, are not unusual and should be carefully inspected. The system operates under high pressure. The fluid is flammable, and if leaking fluid happens to contact a hot engine part, a fire might result. You always want to be sure the hoses and connections are sound.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(200)

Rating Summary
186
9
2
1
2
186
9
2
1
2

Daniel

8 years of experience
18 reviews
Daniel
8 years of experience
Crown Victoria 2008 - Brakes, Steering and Suspension Inspection - Fort Lauderdale, FL
Great mechanic highly recommend him

James

21 years of experience
49 reviews
James
21 years of experience
Crown Victoria 2004 - Oil/Fluid Leak - Douglasville, GA
Good service

Ronnie

28 years of experience
65 reviews
Ronnie
28 years of experience
Crown Victoria 1993 - Tune-up - Franklin, TN
No problem at all. Everything went fine. Ronnie is a great mechanic.

Peter

22 years of experience
479 reviews
Peter
22 years of experience
Crown Victoria 2003 - Power Steering Fluid Service - Chatsworth, CA
Peter is patient, professional, and polite. He knows his stuff.

Excellent Rating

(200)

Rating Summary
186
9
2
1
2
186
9
2
1
2
Number of Ford Crown Victoria services completed
2200+
services done by our mechanics
TOTAL NUMBER OF EXPERT Ford MECHANICS
1800+
experts on our platform

Recent articles & questions

The Most and Least Expensive Cars to Insure
Car insurance quotes depend on the car make and model. The Honda Odyssey is the least expensive and the Dodge Viper is the most expensive to insure.
How to Use Mitchel ProDemand for Car Repair
For the variety of work a mechanic does, Mitchel ProDemand can be great resource for automotive technicians when repairing vehicles.
P2614 OBD-II Trouble Code: Camshaft Position Signal Output Circuit Open
P2614 P2614 code definition The P2614 trouble code identifies an issue with the camshaft position sensor signal output circuit. What the P2614 code means P2614 is a standard OBD-II trouble code dealing with the camshaft position sensor. The code is...

What do the service codes displayed in the Maintenance Minderâ„¢ mean?

While your Maintenance Minder™ is primarily designed to let you know when it’s time for your next oil change, it also displays codes for other needed services based on vehicle mileage. There are several different codes that can be displayed,...

I put new throttle position sensor on now the car wont start i connected everything back on correctly so why wont it crank now ?

Hey there. Replacement of the throttle position sensor on your vehicle is pretty straight forward. There is no adjustment to be made - just remove and replace the sensor and you should be done. If the vehicle isn't starting, you...

Why does my car shake when I break and why does it sound "old" in cold weather after warming up?

The hard starting in cold weather is almost certainl due to a failing battery. A borderline battery can often be pushed over the edge by cold weather. As far as the braking issues is concerned, the most likely cause is...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com