Chevrolet Aveo5 Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(67)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(67)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Chevrolet Aveo5 Tie Rod End Replacement is $140 with $46 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2006 Chevrolet Aveo5L4-1.6LService typeTie Rod End - Front Right Outer ReplacementEstimate$205.99Shop/Dealer Price$238.74 - $314.49
2007 Chevrolet Aveo5L4-1.6LService typeTie Rod End - Rear Right Inner ReplacementEstimate$195.17Shop/Dealer Price$230.23 - $312.88
2010 Chevrolet Aveo5L4-1.6LService typeTie Rod End - Rear Right Outer ReplacementEstimate$190.71Shop/Dealer Price$224.66 - $303.96
2009 Chevrolet Aveo5L4-1.6LService typeTie Rod End - Rear Left Inner ReplacementEstimate$195.17Shop/Dealer Price$230.21 - $312.84
2007 Chevrolet Aveo5L4-1.6LService typeTie Rod End - Front Left Outer ReplacementEstimate$190.71Shop/Dealer Price$224.67 - $303.99
2011 Chevrolet Aveo5L4-1.6LService typeTie Rod End - Front Right Inner ReplacementEstimate$195.17Shop/Dealer Price$230.23 - $312.88
2011 Chevrolet Aveo5L4-1.6LService typeTie Rod End - Rear Right Inner ReplacementEstimate$200.17Shop/Dealer Price$235.10 - $317.64
2008 Chevrolet Aveo5L4-1.6LService typeTie Rod End - Front Right Inner ReplacementEstimate$200.17Shop/Dealer Price$235.47 - $318.30
Show example Chevrolet Aveo5 Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(67)

Rating Summary
63
1
0
1
2
63
1
0
1
2

Russell

24 years of experience
356 reviews
Russell
24 years of experience
Chevrolet Aveo5 L4-1.6L - Cooling/Radiator Fan Motor - Portland, Oregon
I am very satisfied with how Russell repaired my daughter's car. I am in another state and I am very happy with booking through Yourmechanic and the professional way in which Russell handled the repair.

Peter

43 years of experience
1321 reviews
Peter
43 years of experience
Chevrolet Aveo5 L4-1.6L - Neutral Safety Switch - Phoenix, Arizona
Quick efficient and friendly

Jason

23 years of experience
190 reviews
Jason
23 years of experience
Chevrolet Aveo5 L4-1.6L - Catalytic Converter - Nashville, Tennessee
Jason is great and knowledgeable. He takes the time to walk you through the steps as he works. Highly recommended!

Enrique

21 years of experience
244 reviews
Enrique
21 years of experience
Chevrolet Aveo5 L4-1.6L - Other Inspections - Kissimmee, Florida
Extremely professional with a likable demeanor. Enrique was on spot with his recommendations for my vehicle's needs. He was approachable and knowledgeable.

Excellent Rating

(67)

Rating Summary
63
1
0
1
2
63
1
0
1
2
Number of Chevrolet Aveo5 services completed
737+
services done by our mechanics
TOTAL NUMBER OF EXPERT Chevrolet MECHANICS
1600+
experts on our platform

Recent articles & questions

A Buyer’s Guide to the 2012 Toyota Highlander Hybrid
You’re You’re likely already familiar with the much-celebrated Toyota Highlander, but did you know that Toyota has actually offered a hybrid version of everyone’s favorite crossover SUV since 2006? The 2012 Toyota Highlander Hybrid is one of the most exciting...
2012 Hyundai Elantra vs. 2012 Ford Focus: Which One Should I Buy?
The Hyundai Elantra and the Ford Focus are both offerings in the inexpensive compact sedan category, and both represent some of the best offerings in that class. Compact cars are slightly larger than a subcompact, but smaller than a mid-size;...
Cell Phones and Texting: Distracted Driving Laws in Arkansas
Arkansas Arkansas defines distracted driving as drinking, eating, talking on a cell phone, texting, and talking to passengers. It is considered a serious traffic violation, so if you are caught you will get fined. For drivers under 18 years of...

Reduced engine power warning on, disabled throttle

There is a common issue among vehicles of this year model with the throttle position sensors (https://www.yourmechanic.com/services/throttle-position-sensor-replacement) on the throttle bodies. The reduced engine power warning may have also illuminated the Check Engine Light (https://www.yourmechanic.com/services/check-engine-light-is-on-inspection) and stored a faults code....

2008 VW Passat Komfort that is misfiring could it be engine coil? How much might it cost to fix?

It's true that the car you're looking at may just need an ignition coil. It's also true that it might need an ignition module, a fuel injector, an intake manifold, or it may even have valve damage. Many times I've...

I did a brake conversion on my 79 Camaro and went from drum to disc. brakes are spongy.

Hi Clifford. Thanks for contacting us today. Based on your description, it sounds as if you've got a few air bubbles trapped in the brake lines. This is rather common with brake conversion projects, as it can take quite some...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com