BMW 325Ci Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a BMW 325Ci Brake Drum Replacement is $403 with $242 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2004 BMW 325CiL6-2.5L	Service typeBrake Drum Replacement	Estimate$678.92	Shop/Dealer Price$829.54 - $1214.43
2002 BMW 325CiL6-2.5L	Service typeBrake Drum Replacement	Estimate$644.92	Shop/Dealer Price$795.59 - $1180.53
2006 BMW 325CiL6-2.5L	Service typeBrake Drum Replacement	Estimate$644.92	Shop/Dealer Price$795.59 - $1180.52
2003 BMW 325CiL6-2.5L	Service typeBrake Drum Replacement	Estimate$644.92	Shop/Dealer Price$795.52 - $1180.40
2005 BMW 325CiL6-2.5L	Service typeBrake Drum Replacement	Estimate$644.92	Shop/Dealer Price$795.63 - $1180.60
2001 BMW 325CiL6-2.5L	Service typeBrake Drum Replacement	Estimate$644.92	Shop/Dealer Price$795.59 - $1180.52

Show example BMW 325Ci Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(121)

Rating Summary

114

4

0

1

2

114

4

0

1

2

SEE REVIEWS NEAR ME

Miguel

2021 years of experience

58 reviews

Miguel

2021 years of experience

by Frederick

BMW 325Ci L6-2.5L - Battery will not hold a charge Inspection - Winter Garden, Florida

Miguel took care of things very quickly and was overall fun to be around.

Jonathan

17 years of experience

138 reviews

Request Jonathan

Jonathan

17 years of experience

Request Jonathan

by flymejc15

BMW 325Ci L6-2.5L - Valve Cover Gasket - Scottsdale, Arizona

Jonathan was AWESOME! He showed up in an Audi to service my BMW, which I thought was good for me, if he's driving a foreign car, he can certainly work on mine. Did a great job, will continue to use and recommend Yourmechanic....... Thanks so much, John C

Robert

31 years of experience

641 reviews

Robert

31 years of experience

by Steve

BMW 325Ci L6-2.5L - Valve Cover Gasket - San Jose, California

Robert is a very knowledgeable and professional.

Ian

15 years of experience

133 reviews

Ian

15 years of experience

by isaac

BMW 325Ci L6-2.5L - Radiator Hose Repair - Seattle, Washington

Is was great! Showed up a few minutes before he was supposed to. Explained things thoroughly. Was finished in under an hour and was very friendly. Will Definitely use Ian again!

Excellent Rating

(121)

Rating Summary

114

4

0

1

2

114

4

0

1

2

SEE REVIEWS NEAR ME

Recent articles & questions

P3408 OBD-II Trouble Code: Cylinder 1 Deactivation/Exhaust Valve Malfunction

P3408 P3408 code definition P3408 is the fault code for Cyl1 Exhaust Valve Ctrl Circ High. Cyl1 specifies that the issue is likely taking place in engine cylinder number 1. What the P3408 code means Late model vehicles with eight...

P0925 OBD-II Trouble Code: Gear Shift Reverse Actuator Circuit Range/Performance

P0925 means there was an abnormal voltage reading from the gear shift reverse actuator circuit due to faulty reverse gear guide rail or shift shaft.

Signs You Need New Car Tires

Car tires can leak, wear unevenly, and lose contact with the road, all of which make driving unsafe. Rotate your car tires and inspect them regularly.

Radiator is leaking

Hello. When a radiator is leaking, it is an issue which requires immediate attention. If you continue to drive under this condition, you will be running the risk of damaging other cooling system parts and ultimately, this could become very...

Vent hose broke off of battery

The vents are so you will not get battery fumes built up inside the passenger compartment. Hydrogen gas may build up inside the car and can cause a fire hazard. I would not recommend driving it till you fix the...

Gear slipping 1st 2nd

Hello there, thank you for asking about your 2010 Mercedes-Benz C63 AMG. The first thing to check would be the transmission fluid level. A low transmission fluid level from a leak can cause symptoms where the engine speed rises without...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com