Audi Allroad Quattro Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(16)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(16)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Audi Allroad Quattro Tie Rod End Replacement is $194 with $99 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2005 Audi Allroad QuattroV8-4.2LService typeTie Rod End - Rear Left Inner ReplacementEstimate$357.45Shop/Dealer Price$432.19 - $605.23
2002 Audi Allroad QuattroV6-2.7L TurboService typeTie Rod End - Rear Left Outer ReplacementEstimate$293.35Shop/Dealer Price$360.47 - $522.39
2003 Audi Allroad QuattroV6-2.7L TurboService typeTie Rod End - Front Right Outer ReplacementEstimate$293.35Shop/Dealer Price$360.47 - $522.39
2001 Audi Allroad QuattroV6-2.7L TurboService typeTie Rod End - Rear Right Inner ReplacementEstimate$331.45Shop/Dealer Price$406.18 - $579.20
2002 Audi Allroad QuattroV6-2.7L TurboService typeTie Rod End - Rear Right Outer ReplacementEstimate$293.35Shop/Dealer Price$360.50 - $522.44
2004 Audi Allroad QuattroV8-4.2LService typeTie Rod End - Front Left Inner ReplacementEstimate$331.45Shop/Dealer Price$406.23 - $579.29
2005 Audi Allroad QuattroV8-4.2LService typeTie Rod End - Rear Right Outer ReplacementEstimate$298.35Shop/Dealer Price$365.23 - $526.97
2001 Audi Allroad QuattroV6-2.7L TurboService typeTie Rod End - Rear Left Inner ReplacementEstimate$337.95Shop/Dealer Price$413.27 - $586.73
Show example Audi Allroad Quattro Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Audi mechanics

Real customer reviews from Audi owners like you.

Excellent Rating

(16)

Rating Summary
15
1
0
0
0
15
1
0
0
0

Duane

20 years of experience
545 reviews
Duane
20 years of experience
Allroad Quattro 2005 - Brakes, Steering and Suspension System - Cardiff By The Sea, CA
Duane is the man. He goes above and beyond to help out and make you feel comfortable. He is much more thorough than some of the indie shops I have been to. He takes the time do things like use using gauges to measure play in bushings as compared to indie shops that try to feel it by hand.

Excellent Rating

(16)

Rating Summary
15
1
0
0
0
15
1
0
0
0
Number of Audi Allroad Quattro services completed
176+
services done by our mechanics
TOTAL NUMBER OF EXPERT Audi MECHANICS
700+
experts on our platform

Recent articles & questions

A Buyer’s Guide to the 2012 Kia Sportage
The The 2012 Kia Sportage is a compact Sub that offers quality, reliability, and great fuel economy. It has lots of nice features that come standard, an available turbocharged engine, and a sleek looking style that make it attractive to...
Insurance Requirements for Car Registration in Idaho
The The state of Idaho requires that all drivers carry certain types of automotive insurance, or “financial responsibility,” in order to operate a vehicle legally. This is required whether the vehicle is registered or not. The minimum liability insurance required...
Child Seat Safety Laws in Wisconsin
In In Wisconsin, there are laws in place to protect children from injuries or death should they be involved in a motor vehicle accident. These laws govern the use of child safety seats and other restraints, and they are based...

Readiness code for emission

Hello. Since the vehicle sat for that long, you may have to drive it for about 500 miles before it resets. The key is varying your driving. You need to drive it at highway speeds, around town, stop-and-go driving, and...

power steering not working

You probably know this already, but I must mention that driving with the faulty power steering is very dangerous. This is definitely not an issue that can wait. The trouble could be in the power steering pump (https://www.yourmechanic.com/services/power-steering-pump-replacement), belt/tensioner (https://www.yourmechanic.com/services/drive-belt-tensioner-replacement),...

Smoke coming from blower/fan area

Hi there. The blower resistor (https://www.yourmechanic.com/services/cooling-fan-resistor-replacement) and wiring is right there next to the blower and may be what is smoking. I recommend checking the blower wiring and check resistor and wiring to see if something is shorted out. If...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com