Audi A4 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Audi A4 Brake Drum Replacement is $370 with $209 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2016 Audi A4L4-2.0L Turbo	Service typeBrake Drum Replacement	Estimate$644.64	Shop/Dealer Price$786.69 - $1145.87
2006 Audi A4L4-2.0L Turbo	Service typeBrake Drum Replacement	Estimate$585.72	Shop/Dealer Price$721.59 - $1062.13
2002 Audi A4V6-3.0L	Service typeBrake Drum Replacement	Estimate$585.72	Shop/Dealer Price$721.59 - $1062.12
2003 Audi A4V6-3.0L	Service typeBrake Drum Replacement	Estimate$585.72	Shop/Dealer Price$721.52 - $1062.00
1999 Audi A4V6-2.8L	Service typeBrake Drum Replacement	Estimate$579.12	Shop/Dealer Price$713.38 - $1049.00
1997 Audi A4V6-2.8L	Service typeBrake Drum Replacement	Estimate$589.14	Shop/Dealer Price$725.86 - $1068.96
2017 Audi A4L4-2.0L Turbo	Service typeBrake Drum Replacement	Estimate$724.46	Shop/Dealer Price$879.88 - $1308.34
2011 Audi A4L4-2.0L Turbo	Service typeBrake Drum Replacement	Estimate$626.14	Shop/Dealer Price$770.69 - $1135.69

Show example Audi A4 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Audi mechanics

Real customer reviews from Audi owners like you.

Excellent Rating

(388)

Rating Summary

356

15

2

2

13

356

15

2

2

13

SEE REVIEWS NEAR ME

Jose

10 years of experience

285 reviews

Jose

10 years of experience

by Carla

Audi A4 L4-2.0L Turbo - Battery - Tampa, Florida

Great service and attitude!

Scott

36 years of experience

899 reviews

Scott

36 years of experience

by Philip

Audi A4 L4-1.8L Turbo - Window Motor / Regulator Assembly Replacement (Driver Side Front) - Scottsdale, Arizona

Scott was outstanding. Carefully took his time doing the job right in what turned out to be a very complicated repair.

Victor

11 years of experience

211 reviews

Victor

11 years of experience

by Kory

Audi A4 L4-2.0L Turbo - Oil Change - Chesapeake, Virginia

Excellent service

Duane

25 years of experience

510 reviews

Duane

25 years of experience

by Timothy

Audi A4 L4-2.0L Turbo - Check Engine Light is on - Oceanside, California

Did an awesome job!

Excellent Rating

(388)

Rating Summary

356

15

2

2

13

356

15

2

2

13

SEE REVIEWS NEAR ME

Recent articles & questions

The Difference Between Old Cars and Classic Cars

Classic cars tend to be from the 1930s through 1970s and are often Buicks, Cadillacs, and older Mustangs. Old cars tend to be more ordinary makes.

Why Timing Belt Replacements Can Be Tricky

Methods for changing a timing belt vary based on the type of belt. Service and maintenance should be done based on the manufacturer's recommendation.

How to Replace an Oil Filter Housing Gasket on Most Cars

Oil filter housing gaskets fail when the oil light is on, there is oil visibly dripping from the filter, or oil pressure is lower than normal.

My car started shaking and would not accelerate while I was driving. The check engine light turned on also. What cuase that?

This may be caused by a variety of reasons, but the slow acceleration (https://www.yourmechanic.com/services/car-is-slow-to-accelerate-inspection) suggests that you potentially have a clogged catalytic converter (https://www.yourmechanic.com/services/catalytic-converter-replacement) which could cause overheating (https://www.yourmechanic.com/services/car-is-overheating-inspection). I would definitely not recommend driving it under this condition. I...

Can't get the serpentine belt back on

There should be a belt routing diagram either on the trim panel over the radiator or the underside of the hood. If not, most auto parts stores should have repair manuals available for your vehicle. If you would like a...

Replaced power steering pump and still have a hard steering.

Hi there. There is a PML valve that is on the rack and pinion steering on your vehicle. Check to see if the valve is working. The PML valve is is the speed sensitive steering valve for the steering system....

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com