Audi 80 Quattro Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Audi 80 Quattro Brake Drum Replacement is $353 with $229 for parts and $123 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1990 Audi 80 QuattroL5-2.3L	Service typeBrake Drum Replacement	Estimate$656.08	Shop/Dealer Price$802.11 - $1177.19
1991 Audi 80 QuattroL5-2.3L	Service typeBrake Drum Replacement	Estimate$624.08	Shop/Dealer Price$770.16 - $1145.28
1989 Audi 80 QuattroL5-2.3L	Service typeBrake Drum Replacement	Estimate$610.88	Shop/Dealer Price$753.66 - $1118.87
1992 Audi 80 QuattroL5-2.3L	Service typeBrake Drum Replacement	Estimate$624.08	Shop/Dealer Price$770.10 - $1145.16
1988 Audi 80 QuattroL5-2.3L	Service typeBrake Drum Replacement	Estimate$582.39	Shop/Dealer Price$719.94 - $1081.23

Show example Audi 80 Quattro Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Audi mechanics

Real customer reviews from Audi owners like you.

Excellent Rating

(2,427)

Rating Summary

2,252

86

19

12

58

2,252

86

19

12

58

SEE REVIEWS NEAR ME

Victor

11 years of experience

211 reviews

Victor

11 years of experience

by Kory

Audi A4 L4-2.0L Turbo - Oil Change - Chesapeake, Virginia

Excellent service

Edmar

22 years of experience

246 reviews

Edmar

22 years of experience

by Jennifer

Audi Q5 L4-2.0L Turbo - Check Engine Light is on - Carrollton, Texas

Great service

John

20 years of experience

581 reviews

John

20 years of experience

by Erhan

Audi Q5 L4-2.0L Turbo - Brake Pads Replacement (Front, Rear) - Orlando, Florida

Great

Nathan

29 years of experience

260 reviews

Nathan

29 years of experience

by JOHNNY

Audi A4 Quattro V6-2.8L - Car is not starting - Tulsa, Oklahoma

GOOD

Excellent Rating

(2,427)

Rating Summary

2,252

86

19

12

58

2,252

86

19

12

58

SEE REVIEWS NEAR ME

Recent articles & questions

The Best Used Cars to Buy for First Time Car Owners

Owning Owning your very first car is an exciting time in a person’s life. Likely you want to put a lot of thought and research into the process to ensure you get something that meets your needs, is fun to...

Symptoms of a Bad or Failing Windshield Washer Reservoir

Common signs include fluid leaks from below the car, washer fluid not spraying or frequently low, and cracks in the tank.

P2251 OBD-II Trouble Code: O2 Sensor Negative Current Control Circuit/Open Bank 1 Sensor 1

P2251 P2251 code definition O2 Sensor Negative Current Control Circuit/Open Bank 1 Sensor 1 What the P2251 code means P2251 is an OBD-II generic code. The engine control module (ECM) monitors the negative current control of the O2 sensor heater...

Key gets stuck in the ignition and is hard to get out

Provided that you can turn your key to the off position where you would normally pull it out, it appears that the tumblers in your key cylinder are sticking or binding, preventing the key from being extracted. A quick simple...

Transmission shifting hard and thumps.

Hi there. Though there are many issues that can cause the transmission to shift hard in your Cadillac there are some common problems. If the check engine light (https://www.yourmechanic.com/services/check-engine-light-is-on-inspection)is not on, the problem can be caused by a bad engine...

Cruise control broken

Hi. Cruise control systems only engage past about 35 mph, so make sure that is not the issue. Other issues that can sometimes interfere with the cruise control are brake lights that may be having connection issues. The system uses...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com