Suzuki Verona Brake Drum Replacement Costs

Car	Service	Estimate	Shop/Dealer Price
2004 Suzuki VeronaL6-2.5L	Service typeBrake Drum Replacement	Estimate$679.12	Shop/Dealer Price$817.04 - $1192.52
2005 Suzuki VeronaL6-2.5L	Service typeBrake Drum Replacement	Estimate$645.12	Shop/Dealer Price$783.07 - $1158.57
2006 Suzuki VeronaL6-2.5L	Service typeBrake Drum Replacement	Estimate$645.12	Shop/Dealer Price$783.06 - $1158.57

Car

Service

Estimate

Shop/Dealer Price

2004 Suzuki VeronaL6-2.5L

Service typeBrake Drum Replacement

Estimate$679.12

Shop/Dealer Price$817.04 - $1192.52

2005 Suzuki VeronaL6-2.5L

Service typeBrake Drum Replacement

Estimate$645.12

Shop/Dealer Price$783.07 - $1158.57

2006 Suzuki VeronaL6-2.5L

Service typeBrake Drum Replacement

Estimate$645.12

Shop/Dealer Price$783.06 - $1158.57

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Suzuki mechanics

Real customer reviews from Suzuki owners like you.

Excellent Rating

(6)

Rating Summary

SEE REVIEWS NEAR ME

Eric

12 years of experience

230 reviews

Request Eric

by Dheeraj

Suzuki Verona L6-2.5L - Valve Cover Gasket - Raleigh, North Carolina

Eric is a very knowledgeable and experienced mechanic. The job, valve cover replacement for my car is one of the difficult ones. It is complicated because many components, electrical connections and hoses had to come off before he could get to the valve cover. He was very patient and meticulous with the job and made sure everything is working fine.

Melvin

14 years of experience

158 reviews

Request Melvin

by Daniel

Suzuki Verona L6-2.5L - Check Engine Light is on - Portsmouth, Virginia

Melvin was a pleasure to meet and be around. Extremely courteous and polite. Above all else knowledgeable. If Melvin is available I will be using him every time. Highly recommended?

Joshua

27 years of experience

709 reviews

Request Joshua

by Riaz

Suzuki Verona L6-2.5L - Engine idle speed is high - Walnut Creek, California

I have nothing but praises for Joshua. He has this incredible ability to troubleshoot issues with cars and armed with knowledge on the subject to his teeth. On top of that, he is also extremely proficient in fixing car issues that do not require troubleshooting. I was so impressed with Josh's sincerity and professionalism that I ended up getting 8 services done in the past month and a half. Of course, for every service, I requested for Josh. When Josh first came to service my car (simple oil change), I was on the verge of getting ready to dispose the car off (a 2004 Suzuki Verona EX, with just 68,000 miles). All thanks to Josh, the car is running better than when it was new (I am serious ... the brand new car had engine trouble and the dealer agreed to replace the engine after a good fight). It is now a pleasure to drive the car and I hope to use it for another 5 years, at least. I strongly recommend Josh to one and all if you ever happen to use YourMechanic.com. For all my car service needs, I will rely on Josh and YourMechanic.com from now on.

Suzuki Verona L6-2.5L - 67,500 Miles Maintenance Service - Walnut Creek, California

Suzuki Verona Brake Drum Replacement at your home or office.

Estimate price near me

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Suzuki Verona Brake Drum Replacement is $403 with $242 for parts and $161 for labor. Prices may vary depending on your location.

What are brake drums and how do they work?

When to consider replacing brake drums:

How do mechanics replace brake drums?

Is it safe to drive with a brake drum problem?

When replacing brake drums keep in mind:

Meet some of our expert Suzuki mechanics

Excellent Rating

Rating Summary

Eric

Melvin

Joshua

Joshua

Excellent Rating

Rating Summary

Recent articles & questions

Debating installation of a leveling kit

Jerking reaction when accelerating

Will a new oil pump stop the possible valve ticking in my 2004 Subaru Impreza when its cold and what should I put in the transmission

How can we help?