Mitsubishi Raider Water Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

customer ratings

(12)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

customer ratings

(12)

Water Pump Replacement Estimate for Mitsubishi Raider

Mitsubishi Raider Water Pump Replacement costs $270 on average.

CarServiceEstimateShop/Dealer Price
2007 Mitsubishi RaiderV6-3.7LService typeWater Pump ReplacementEstimate$424.95Shop/Dealer Price$513.55 - $740.29
2006 Mitsubishi RaiderV6-3.7LService typeWater Pump ReplacementEstimate$396.95Shop/Dealer Price$485.57 - $712.33
2006 Mitsubishi RaiderV8-4.7LService typeWater Pump ReplacementEstimate$396.95Shop/Dealer Price$485.57 - $712.33
2008 Mitsubishi RaiderV6-3.7LService typeWater Pump ReplacementEstimate$396.95Shop/Dealer Price$485.54 - $712.27
2009 Mitsubishi RaiderV6-3.7LService typeWater Pump ReplacementEstimate$396.95Shop/Dealer Price$485.59 - $712.37
2007 Mitsubishi RaiderV8-4.7LService typeWater Pump ReplacementEstimate$396.95Shop/Dealer Price$485.57 - $712.33
Show example Mitsubishi Raider Water Pump Replacement prices

Water Pump Replacement Service

What is a water pump and how does it work?

The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley. The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.

When to consider replacing the water pump:

  • Coolant leaks or overheating. The water pump impeller shaft is supported by a bearing. Eventually, the bearing or seal can wear and leak or damage the impeller. Many water pumps have weep holes near the pump bearing. If you see significant leakage from that weep hole, it is time to replace the pump.
  • Bearing roughness or noise. If the water pump shaft does not turn smoothly or the pump is noisy, the bearing is excessively worn. Pump replacement will be necessary.
  • Timing belt replacement. In engines where the water pump is driven by the timing belt, it is a good idea to replace the water pump at the same time the timing belt is replaced. The extensive work explains why it is always recommended to replace the water pump whenever the mechanic already has these components removed for regularly scheduled timing belt replacement.

How do mechanics replace the water pump?

  • The water pump is usually bolted to the front of the engine. The replacement procedure will vary depending on whether the pump is driven by the timing belt, the serpentine belt, or chain.
  • On a cold engine, the engine coolant is drained to a level below the water pump.
  • Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump.
  • The bolts holding the pump to the engine are removed and the pump is pulled out.
  • The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
  • For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air. The engine is then run and brought to normal operating temperature to check for leaks and ensure normal operating temperature.

Is it safe to drive with a water pump problem?

No. Should the water pump only leak a little bit, you can drive the car. However, a small leak could suddenly enlarge or the pump bearing might unexpectedly seize. Either circumstance would likely cause engine overheating. If a defective water pump causes the overheating, it is not safe to drive because of the damage to the engine.

When replacing the water pump keep in mind:

  • It is best to install a new cooling system thermostat when you install a new water pump, especially if the thermostat is old or original.
  • Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement.
  • The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mitsubishi mechanics

Real customer reviews from Mitsubishi owners like you.

Excellent Rating

(12)

Rating Summary
12
0
0
0
0
12
0
0
0
0

Excellent Rating

(12)

Rating Summary
12
0
0
0
0
12
0
0
0
0
Number of Mitsubishi Raider services completed
132+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mitsubishi MECHANICS
700+
experts on our platform

Recent articles & questions

What Is the Difference Between Climate Control and Air Conditioning
It’s It’s important to be able to control the temperature inside your car’s cabin. During the summer, you need air conditioning to ensure comfort and safety, and during the winter, you’ll need heat for the same reason. However, different cars...
Rules of the Road For Montana Drivers
When When you are driving in your home state, you likely know all the rules that you need to follow on the roads. While many of the traffic laws are based on common sense and following posted signs and signals...
P2568 OBD-II Trouble Code: Direct O-Zone Reduction Catalyst Temperature Sensor Circuit Range/Performance
P2568 P2568 code definition Direct O-zone Reduction Catalyst Temperature Sensor Circuit Range/Performance What the P2568 code means P2568 is an OBD-II generic code that the engine control module (ECM) has detected the engine o-zone reduction catalyst temperature sensor to be...

Car has CVT transmission, can't afford to replace, can I just replace the entire motor with a used one with different trans?

Hello. If you wanted to replace the motor and transmission, you would have other problems like the wire harnesses and ECM modules among other problems to do the swap correctly. You may be better off replacing the transmission with a...

Catalytic converter replacement

Hello. It's quite possible that there is no one at fault here. It may just be unfortunate timing. I'm assuming that you have had the codes read and that is why you have decided you need to replace the catalytic...

When im at stop light press on gas car jerks

Hi There, It sounds like your vehicle may be a bit low on transmission fluid or you may potentially have a bad transmission control solenoid. As you know, the transmission works on hydraulic pressure built up from the fluid inside...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com