Mercedes-Benz SL600 Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(5)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(5)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Mercedes-Benz SL600 Tie Rod End Replacement is $114 with $19 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2011 Mercedes-Benz SL600V12-5.5L TurboService typeTie Rod End - Front Right Outer ReplacementEstimate$166.89Shop/Dealer Price$197.37 - $249.42
2004 Mercedes-Benz SL600V12-5.5L TurboService typeTie Rod End - Rear Left Outer ReplacementEstimate$479.35Shop/Dealer Price$592.97 - $894.39
2004 Mercedes-Benz SL600V12-5.5L TurboService typeTie Rod End - Front Left Outer ReplacementEstimate$479.35Shop/Dealer Price$592.97 - $894.39
2008 Mercedes-Benz SL600V12-5.5L TurboService typeTie Rod End - Front Left Outer ReplacementEstimate$479.35Shop/Dealer Price$592.93 - $894.32
2005 Mercedes-Benz SL600V12-5.5L TurboService typeTie Rod End - Front Right Inner ReplacementEstimate$244.57Shop/Dealer Price$299.52 - $424.88
2006 Mercedes-Benz SL600V12-5.5L TurboService typeTie Rod End - Front Left Outer ReplacementEstimate$479.35Shop/Dealer Price$592.97 - $894.39
1996 Mercedes-Benz SL600V12-6.0LService typeTie Rod End - Front Right Inner ReplacementEstimate$311.15Shop/Dealer Price$381.23 - $552.57
2005 Mercedes-Benz SL600V12-5.5L TurboService typeTie Rod End - Rear Left Outer ReplacementEstimate$484.35Shop/Dealer Price$598.39 - $900.11
Show example Mercedes-Benz SL600 Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(5)

Rating Summary
4
0
0
0
1
4
0
0
0
1

Steven

14 years of experience
425 reviews
Steven
14 years of experience
Mercedes-Benz SL600 V12-6.0L - Loud screeching noise when I start the car - Goodyear, Arizona
I have an older Mercedes 600SL and was somewhat concerned about using some one other than a dealer, but my fears were put to rest after my initial conversation with Steve. Steve was on time, knowledgeable, had all of the required tools. diagnose the problem and gave me a stalemate of cost for the repair. He did not try to over sale me on something I didn't need. He made the repairs made sure that everything was correct and assured me that if I needed anything more he was just a phone call awaly. Steve called me the next day just to check that the repair was good.

Richard

21 years of experience
461 reviews
Richard
21 years of experience
Mercedes-Benz SL600 V12-6.0L - Car is not starting - Marietta, Georgia
Fast honest knew what he needed

Chris

22 years of experience
2229 reviews
Chris
22 years of experience
Mercedes-Benz SL600 V12-5.5L Turbo - Brake Pads Replacement (Front) - Huntington Beach, California
Highly recommend Chris and will request him next time I need service on my Mercedes SL600 V12 Turbo Roadster! Chris is an expert craftsman who really knows about my Mercedes. I was happy about saving money by not going to the dealer for service. Who knew you can have your car serviced at home while getting things done around the house instead of wasting time driving to a dealer and hanging out in their waiting area! I will definitely request Chris next time my car needs service!!

Edwin

40 years of experience
36 reviews
Edwin
40 years of experience
Mercedes-Benz SL600 V12-5.5L Turbo - Car does not shift from park to drive - Mount Pleasant, South Carolina
Great

Excellent Rating

(5)

Rating Summary
4
0
0
0
1
4
0
0
0
1
Number of Mercedes-Benz SL600 services completed
55+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

A Buyer’s Guide to the 2012 GMC Acadia
When When it comes to finding the right SUV for your family, it seems like there are always a lot of compromises to be made. One vehicle is so performance and off-road oriented that you can’t imagine taking your kids...
A Buyer’s Guide to the 2011 Mercedes-Benz ML450 Hybrid
The The 2011 Mercedes-Benz ML450 Hybrid is Mercedes' first hybrid SUV. It can perform light off-roading tasks while still being able to tow a good amount of weight. It has excellent fuel economy and drives just like the Mercedes-Benz M-Class...
Driving Laws and Permits in the State of Indiana
Whether Whether you are a disabled driver or not, it is important to understand the disabled driver laws in your state. Each state has its own specific requirements and regulations for disabled drivers. Indiana is no exception. What types of...

How do I turn the electronic stability control (ESC) off?

The electronic stability control (ESC) system helps keep your car stable when it is cornering, and when you are driving in dangerous weather conditions. If you would like to turn the ESC off, you can do so by pressing the...

What should it cost to replace ac compressor, accumulator

It takes roughly 12 hours to replace the compressor and expansion valve. As you may know, the expansion valve is attached to the evaporator under the dash and thus is not readily accessible, hence the hours. If you input your...

Load noise after changing belt andpully still grinding sound like its hitting something is water pump bad

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com