Mercedes-Benz SL600 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mercedes-Benz SL600 Brake Drum Replacement is $352 with $219 for parts and $133 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2008 Mercedes-Benz SL600V12-5.5L Turbo	Service typeBrake Drum Replacement	Estimate$600.59	Shop/Dealer Price$734.99 - $1083.07
2006 Mercedes-Benz SL600V12-5.5L Turbo	Service typeBrake Drum Replacement	Estimate$572.59	Shop/Dealer Price$707.03 - $1055.14
2005 Mercedes-Benz SL600V12-5.5L Turbo	Service typeBrake Drum Replacement	Estimate$572.59	Shop/Dealer Price$707.03 - $1055.14
1997 Mercedes-Benz SL600V12-6.0L	Service typeBrake Drum Replacement	Estimate$571.69	Shop/Dealer Price$705.85 - $1053.24
2001 Mercedes-Benz SL600V12-6.0L	Service typeBrake Drum Replacement	Estimate$571.69	Shop/Dealer Price$705.94 - $1053.41
2000 Mercedes-Benz SL600V12-6.0L	Service typeBrake Drum Replacement	Estimate$615.07	Shop/Dealer Price$760.13 - $1140.10
1996 Mercedes-Benz SL600V12-6.0L	Service typeBrake Drum Replacement	Estimate$622.07	Shop/Dealer Price$766.80 - $1146.51
2009 Mercedes-Benz SL600V12-5.5L Turbo	Service typeBrake Drum Replacement	Estimate$579.59	Shop/Dealer Price$714.61 - $1063.15

Show example Mercedes-Benz SL600 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(5)

Rating Summary

4

0

0

0

1

4

0

0

0

1

SEE REVIEWS NEAR ME

Chris

22 years of experience

2241 reviews

Chris

22 years of experience

by Susan

Mercedes-Benz SL600 V12-5.5L Turbo - Brake Pads Replacement (Front) - Huntington Beach, California

Highly recommend Chris and will request him next time I need service on my Mercedes SL600 V12 Turbo Roadster! Chris is an expert craftsman who really knows about my Mercedes. I was happy about saving money by not going to the dealer for service. Who knew you can have your car serviced at home while getting things done around the house instead of wasting time driving to a dealer and hanging out in their waiting area! I will definitely request Chris next time my car needs service!!

Richard

21 years of experience

461 reviews

Request Richard

Richard

21 years of experience

Request Richard

by Chhuk

Mercedes-Benz SL600 V12-6.0L - Car is not starting - Marietta, Georgia

Fast honest knew what he needed

Steven

14 years of experience

425 reviews

Steven

14 years of experience

by Richard

Mercedes-Benz SL600 V12-6.0L - Loud screeching noise when I start the car - Goodyear, Arizona

I have an older Mercedes 600SL and was somewhat concerned about using some one other than a dealer, but my fears were put to rest after my initial conversation with Steve. Steve was on time, knowledgeable, had all of the required tools. diagnose the problem and gave me a stalemate of cost for the repair. He did not try to over sale me on something I didn't need. He made the repairs made sure that everything was correct and assured me that if I needed anything more he was just a phone call awaly. Steve called me the next day just to check that the repair was good.

Edwin

40 years of experience

36 reviews

Edwin

40 years of experience

by Stacy

Mercedes-Benz SL600 V12-5.5L Turbo - Car does not shift from park to drive - Mount Pleasant, South Carolina

Great

Excellent Rating

(5)

Rating Summary

4

0

0

0

1

4

0

0

0

1

SEE REVIEWS NEAR ME

Recent articles & questions

How to Renew Your Car Registration in Hawaii

Among Among the most beautiful states in the country is Hawaii. There are a number of advantages that come to living in this state. Just like any other state, Hawaii will require you to register the vehicles that you have...

How to Replace a Lost or Stolen Car Title in Arkansas

Your Your car title does more than just prove that you are the legal owner. It allows you to sell your car when the time comes, or trade it in for a new vehicle. It will also be required if...

P0316 OBD-II Trouble Code: Misfire Detected on Startup (First 1000 Revolutions)

P0316 means the engine is misfiring due to damaged or defective ignition system components or engine vacuum leaks.

I think my starter is misaligned.

This is often times a result of the starter solenoid being misaligned and not reaching out far enough to the flywheel. You will notice on the starter solenoid there are bolt holes that allow for a slight adjustment. This allows...

my car was at a stop light, started to chug as if it were running out of gas, then died and wouldn't start.

Any number of things could have occurred. On the outside chance, it could be another failed fuel pump. Unusual but it has happened. If it is not getting fuel, it could be components like a failed fuel pressure regulator or...

Why would someone charge me $600.00 to replace battery cable-positive side?

Hello - on some vehicles, the positive battery cable is quite long, going from the starter to the rear passenger seat or trunk area - literally 15' long. Besides costing quite a bit for the part, the labor to install...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com