Mercedes-Benz GLK250 Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(5,670)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(5,670)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mercedes-Benz GLK250 Brake Drum Replacement is $391 with $230 for parts and $161 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2014 Mercedes-Benz GLK250L4-2.1L Turbo DieselService typeBrake Drum ReplacementEstimate$654.96Shop/Dealer Price$799.59 - $1166.51
2015 Mercedes-Benz GLK250L4-2.1L Turbo DieselService typeBrake Drum ReplacementEstimate$620.96Shop/Dealer Price$765.64 - $1132.61
2013 Mercedes-Benz GLK250L4-2.1L Turbo DieselService typeBrake Drum ReplacementEstimate$620.96Shop/Dealer Price$765.64 - $1132.60
Show example Mercedes-Benz GLK250 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(5,670)

Rating Summary
5,278
191
54
28
119
5,278
191
54
28
119

Armando

32 years of experience
33 reviews
Armando
32 years of experience
Mercedes-Benz GLK250 L4-2.1L Turbo Diesel - Oil Change - Del Mar, California
Armando was great

Richard

21 years of experience
237 reviews
Richard
21 years of experience
Mercedes-Benz GLK250 L4-2.1L Turbo Diesel - Oil Change - Fort Myers, Florida
Arrived early, fast and efficient. Thanks.

Chris

22 years of experience
2252 reviews
Chris
22 years of experience
Mercedes-Benz ML320 V6-3.2L - Water Pump Replacement - Dana Point, California
thanks chris outstanding job

John

27 years of experience
1040 reviews
John
27 years of experience
Mercedes-Benz GLK350 V6-3.5L - Loud screeching noise when I start the car - Pearland, Texas
Seriously the best mechanic I’ve ever dealt with. He’s so precise with his diagnostic testing. He gives great advice and he’s definitely cost efficient. He treats you like family. I definitely recommend him to every single person.

Excellent Rating

(5,670)

Rating Summary
5,278
191
54
28
119
5,278
191
54
28
119
Number of Mercedes-Benz services completed
62370+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

How to Get an Iowa Driver's Permit
Like Like most states, Iowa requires all underage drivers to participate in a Graduated Driver Licensing program. This program states that those under 18 must obtain a learner’s permit that graduates to a full license as the driver gains experience...
What are the Car Pool Rules in Idaho?
Idaho Idaho is a beautiful and rural state, and as a result its scenic drives (https://www.yourmechanic.com/article/top-10-scenic-drives-in-idaho) are much better known than its freeways. However, as with all states, freeways are responsible for getting a large number of Idaho citizens to...
P0962 OBD-II Trouble Code: Pressure Control Solenoid A Control Circuit Low
P9062 means voltage from the pressure control solenoid control circuit that is abnormally low due to electrical issues, fluid levels, or blockages.

How often should I have my steering system checked?

Just like your brakes (https://www.yourmechanic.com/article/how-do-i-know-if-my-brakes-need-replacing), your steering system (https://www.yourmechanic.com/article/how-often-should-the-steering-system-be-inspected) is an essential part to the control and safety of your vehicle. Safety is a huge concern with both of these systems since a brake failure can keep you from stopping...

What’s wrong if the starter works, but the engine won’t crank?

While the most common problem with the engine is a dead battery, there are other things that could be causing a no start situation. If you turn the key and the starter engages normally but the engine doesn’t crank, here...

Truck is overheating even after replacements

Hello. It is possible that your heater core is clogged, which may cause a vehicle to overheat (https://www.yourmechanic.com/article/what-causes-a-car-to-overheat). It is also possible that after having other components replaced, there could be air trapped in the cooling system. This may cause...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com