Mercedes-Benz GLE550e Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(5,576)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(5,576)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mercedes-Benz GLE550e Brake Drum Replacement is $499 with $338 for parts and $161 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2016 Mercedes-Benz GLE550eV6-3.0L Turbo HybridService typeBrake Drum ReplacementEstimate$871.24Shop/Dealer Price$1057.19 - $1576.76
2017 Mercedes-Benz GLE550eV6-3.0L Turbo HybridService typeBrake Drum ReplacementEstimate$837.24Shop/Dealer Price$1023.22 - $1542.81
2018 Mercedes-Benz GLE550eV6-3.0L Turbo HybridService typeBrake Drum ReplacementEstimate$837.24Shop/Dealer Price$1023.21 - $1542.81
Show example Mercedes-Benz GLE550e Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(5,576)

Rating Summary
5,188
189
54
28
117
5,188
189
54
28
117

Joseph

17 years of experience
67 reviews
Joseph
17 years of experience
Mercedes-Benz GLA250 L4-2.0L Turbo - Steering wheel is hard to turn Inspection - Boca Raton, Florida
Joseph was great! He’s professional, very friendly and really sharp mechanic. Definitely recommend! 5 Stars ⭐️

Travis

13 years of experience
160 reviews
Travis
13 years of experience
Mercedes-Benz C300 V6-3.0L - Spark Plugs - Matthews, North Carolina
There is nothing a person with car issues love more than an HONEST MECHANIC. Travis serviced my C300 Mercedes by replacing my sparks plugs. Initially the service was suggested to be roughly $400. Well, Travis was not only on time and ready to get the job done, but he notified me that additional parts and labor wasn’t needed as part of the service which reduced the bill by $100. I understand that driving foreign can get quite expensive. However we all know, in many cases mechanics will not inform you of this and will still charge you, if not more. I appreciate his time, attentiveness, and honest service. He completed the job very quickly as well. I can already tell the difference in the performance of the vehicle. Thanks Travis, you have my stamp of approval and Im looking forward to having you service my car again in the future.

Jeremy

20 years of experience
603 reviews
Jeremy
20 years of experience
Mercedes-Benz E320 V6-3.2L - Crankshaft Position Sensor - West Palm Beach, Florida
Total satisfied with Jeremy's work. I would like for him to work on my other car. I'm waiting for him to give me the cuote, to find out if it's a reasanable one. Thank you so much.

Derrick

11 years of experience
171 reviews
Derrick
11 years of experience
Mercedes-Benz E430 V8-4.3L - Oil Change - Vallejo, California
Derrick is prompt and very thorough with his work.

Excellent Rating

(5,576)

Rating Summary
5,188
189
54
28
117
5,188
189
54
28
117
Number of Mercedes-Benz services completed
61336+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

How Long Does a Distributor O Ring Last?
The The distributor is part of the ignition system in your vehicle and its purpose is to route high voltage from the ignition coil to the spark plug. The spark plug then ignites the fuel and air mixture in the...
How to Buy a New Car Below Sticker Price
When When you buy a new car from the car dealership, you want to get a better deal than they have advertised or displayed on the car, but negotiation isn’t a strong suit for every person. There are several ways...
P2090 OBD-II Trouble Code: 'B' Camshaft Position Actuator Control Circuit Low Bank 1
P2090 P2090 Code Definition The P2090 code is a generic powertrain code related to fuel and air metering and auxiliary emission controls. This code appears when the engine control module (ECM) has detected variances between camshaft B and the crankshaft...

How do I use the dome light?

Your car’s dome light provides important illumination when entering or exiting the vehicle, particularly in low-light situations. However, you can adjust its operation so that it works (or doesn’t) when you want it. Here’s how: Locate the dome light. It’s...

Car shuts down when in reverse

It appears that you may be experiencing a few different issues with your Honda Accord. The stalling may be caused by such culprits as a dirty idle air control valve or perhaps it may be time to perform a valve...

My heater blows cold on the driver side and hot on the passenger side. I do not have duel temperature control

Hi Scott. Your Wrangler has a blend door that circulates heat and cool air (from AC operation) to different side vents. In most cases, when you have an issue as you've described, this component is damaged, or there is something...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com