Mercedes-Benz E550 Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(58)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(58)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Mercedes-Benz E550 Tie Rod End Replacement is $146 with $51 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2015 Mercedes-Benz E550V8-4.7L TurboService typeTie Rod End - Rear Right Inner ReplacementEstimate$337.51Shop/Dealer Price$403.14 - $577.53
2008 Mercedes-Benz E550V8-5.5LService typeTie Rod End - Front Left Outer ReplacementEstimate$302.95Shop/Dealer Price$372.47 - $541.59
2016 Mercedes-Benz E550V8-4.7L TurboService typeTie Rod End - Front Right Outer ReplacementEstimate$317.51Shop/Dealer Price$383.16 - $557.56
2007 Mercedes-Benz E550V8-5.5LService typeTie Rod End - Rear Left Inner ReplacementEstimate$244.57Shop/Dealer Price$299.46 - $424.76
2007 Mercedes-Benz E550V8-5.5LService typeTie Rod End - Front Left Outer ReplacementEstimate$302.95Shop/Dealer Price$372.50 - $541.64
2010 Mercedes-Benz E550V8-5.5LService typeTie Rod End - Rear Right Inner ReplacementEstimate$252.65Shop/Dealer Price$309.60 - $440.99
2007 Mercedes-Benz E550V8-5.5LService typeTie Rod End - Rear Left Outer ReplacementEstimate$307.95Shop/Dealer Price$377.23 - $546.17
2007 Mercedes-Benz E550V8-5.5LService typeTie Rod End - Rear Right Inner ReplacementEstimate$249.57Shop/Dealer Price$304.91 - $430.55
Show example Mercedes-Benz E550 Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(58)

Rating Summary
54
1
1
0
2
54
1
1
0
2

Joseph

27 years of experience
578 reviews
Joseph
27 years of experience
Mercedes-Benz E550 V8-5.5L - Alternator - Cypress, Texas
He did a great job ...

Donald

40 years of experience
124 reviews
Donald
40 years of experience
Mercedes-Benz E550 V8-5.5L - Oil Change - Atlanta, Georgia
Very through. Showed up on time and even advised not to get my breaks redone.

David

16 years of experience
637 reviews
David
16 years of experience
Mercedes-Benz E550 V8-5.5L - Tail Light Lens Replacement (Driver Side) - Crockett, California
efficient as always

Peter

43 years of experience
1321 reviews
Peter
43 years of experience
Mercedes-Benz E550 V8-5.5L - Oil Change - Waddell, Arizona
Peter is very knowledgeable with regards to my Mercedes. When I booked the 80K maintenance, I was expecting all necessary services to be completed. Instead there were several actions that Peter told me were due at the 80K mile mark as identified by the service levels, but they were not done (e.g.; replacing a filter; replacing spark plugs). I now have a quote for an additional $1300 to complete those items plus problems discovered during the inspection.

Excellent Rating

(58)

Rating Summary
54
1
1
0
2
54
1
1
0
2
Number of Mercedes-Benz E550 services completed
638+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

How Long Does an Oil Pump O Ring Last?
The The effort that goes into keeping a car in good shape is worth it. Taking the time to make sure that all of the vital components of your engine are working properly is an essential part of keeping your...
How to Get an Alabama Driver's Permit
In In order to legally drive on the roads of Alabama, anyone who lives in the state must have an Alabama driver’s license. There are two types of driver’s licenses in Alabama: a driver’s license, and a learner’s license, or...
What Does the Headlight Range Control Warning Light Mean?
The headlight range control warning light alerts you when the control system is defective and needs service or repair.

What are toggle switches and how are they used in cars?

Toggle switches are a simple type of electrical switch that is manually operated by the user using a short handle or lever. When the user presses the short handle forward or backwards the switch is moved between positions. When the...

High pitch frequency noise

The high pitch noise you are hearing is the fuel pump in the fuel tank getting noisey and will fail if the pump is not changed in the near future. The fuel filter and fuel pump along with the fuel...

Car shuts off in neutral and in park

Hello. We will be happy to assist you. There are few things that I recommend you have a technician check on your vehicle. Being that coolant sprayed everywhere they would want to check the electrical connectors and wiring for any...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com