Mercedes-Benz E420 Water Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(18)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(18)

Water Pump Replacement Service

How much does a Water Pump Replacement cost?

On average, the cost for a Mercedes-Benz E420 Water Pump Replacement is $649 with $240 for parts and $408 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1995 Mercedes-Benz E420V8-4.2LService typeWater Pump ReplacementEstimate$1158.94Shop/Dealer Price$1382.33 - $1820.16
1997 Mercedes-Benz E420V8-4.2LService typeWater Pump ReplacementEstimate$888.96Shop/Dealer Price$1084.48 - $1501.40
1994 Mercedes-Benz E420V8-4.2LService typeWater Pump ReplacementEstimate$1040.94Shop/Dealer Price$1264.50 - $1702.45
Show example Mercedes-Benz E420 Water Pump Replacement prices

What is a water pump and how does it work?

The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley. The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.

When to consider replacing the water pump:

  • Coolant leaks or overheating. The water pump impeller shaft is supported by a bearing. Eventually, the bearing or seal can wear and leak or damage the impeller. Many water pumps have weep holes near the pump bearing. If you see significant leakage from that weep hole, it is time to replace the pump.
  • Bearing roughness or noise. If the water pump shaft does not turn smoothly or the pump is noisy, the bearing is excessively worn. Pump replacement will be necessary.
  • Timing belt replacement. In engines where the water pump is driven by the timing belt, it is a good idea to replace the water pump at the same time the timing belt is replaced. The extensive work explains why it is always recommended to replace the water pump whenever the mechanic already has these components removed for regularly scheduled timing belt replacement.

How do mechanics replace the water pump?

  • The water pump is usually bolted to the front of the engine. The replacement procedure will vary depending on whether the pump is driven by the timing belt, the serpentine belt, or chain.
  • On a cold engine, the engine coolant is drained to a level below the water pump.
  • Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump.
  • The bolts holding the pump to the engine are removed and the pump is pulled out.
  • The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
  • For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air. The engine is then run and brought to normal operating temperature to check for leaks and ensure normal operating temperature.

Is it safe to drive with a water pump problem?

No. Should the water pump only leak a little bit, you can drive the car. However, a small leak could suddenly enlarge or the pump bearing might unexpectedly seize. Either circumstance would likely cause engine overheating. If a defective water pump causes the overheating, it is not safe to drive because of the damage to the engine.

When replacing the water pump keep in mind:

  • It is best to install a new cooling system thermostat when you install a new water pump, especially if the thermostat is old or original.
  • Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement.
  • The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(18)

Rating Summary
14
2
1
0
1
14
2
1
0
1

Bill

15 years of experience
23 reviews
Bill
15 years of experience
E420 1997 - Air Filter - Aliso Viejo, CA
Very professional, showed up promptly, and was honest in his diagnosis. Great service!

Bill

15 years of experience
23 reviews
Bill
15 years of experience
E420 1997 - Serpentine/Drive Belt - Aliso Viejo, CA
Very professional, showed up promptly, and was honest in his diagnosis. Great service!

James

21 years of experience
49 reviews
James
21 years of experience
E420 1997 - Steering Rack/Gearbox - Marietta, GA
Excellent service. Very knowledgeable and meticulous, ensuring that the work is flawless before he leaves. I highly recommend James.

Excellent Rating

(18)

Rating Summary
14
2
1
0
1
14
2
1
0
1
Number of Mercedes-Benz E420 services completed
198+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1000+
experts on our platform

Recent articles & questions

P2104 OBD-II Trouble Code: Throttle Actuator Control System Forced Idle
P2104 P2104 trouble code definition Throttle Actuator Control System Forced Idle What the P2104 code means P2104 is an OBD-II generic code for the engine control module (ECM) detecting a major failure in the throttle actuator control (TAC) system causing...
P2734 OBD-II Trouble Code: Pressure Control Solenoid E Stuck On
P2734 means a transmission solenoid has malfunctioned due to a failing transmission, bad sensor or solenoid, low fluid level or other electrical issue
Synthetic Oil: Should You Upgrade From Conventional to Synthetic?
The benefits of full synthetic oil for car engines.

Car will not accelerate properly

That was smart to check fluid levels under the hood before your trip. I'm not sure you could've done anything else to prevent this breakdown. It sounds like you are describing a transmission failure on the Quest. A mechanic with...

Will a bottle of Lucas transmission fluid fix my issue?

Hi there, thanks for writing in. Although Lucas makes an exceptional transmission fluid stabilizer, you should try to find out why the transmission is damaged in the first place. If the fluid level was drained to the right level and...

Engine lock

If a mechanic already looked at it and says engine is locked then I would need to know if the engine was overheated or ran without oil. Either way you may need to replace the motor. If the motor needs...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com