Mercedes-Benz CLK550 Brake Pad Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(17)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(17)

Brake Pad Replacement Service

How much does a Brake Pad Replacement cost?

On average, the cost for a Mercedes-Benz CLK550 Brake Pad Replacement is $176 with $81 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2008 Mercedes-Benz CLK550V8-5.5LService typeBrake Pads - Front ReplacementEstimate$287.41Shop/Dealer Price$348.02 - $490.46
2007 Mercedes-Benz CLK550V8-5.5LService typeBrake Pads - Rear ReplacementEstimate$257.39Shop/Dealer Price$315.52 - $450.47
2007 Mercedes-Benz CLK550V8-5.5LService typeBrake Pads - Front ReplacementEstimate$267.41Shop/Dealer Price$328.05 - $470.51
2008 Mercedes-Benz CLK550V8-5.5LService typeBrake Pads - Rear ReplacementEstimate$257.39Shop/Dealer Price$315.48 - $450.40
2009 Mercedes-Benz CLK550V8-5.5LService typeBrake Pads - Front ReplacementEstimate$267.41Shop/Dealer Price$328.07 - $470.56
2009 Mercedes-Benz CLK550V8-5.5LService typeBrake Pads - Rear ReplacementEstimate$257.39Shop/Dealer Price$315.52 - $450.47
Show example Mercedes-Benz CLK550 Brake Pad Replacement prices

What are brake pads and how do they work?

Brake pads consist of friction material that is bonded to a sturdy steel backing plate. When you push on the brake pedal, the friction material on the brake pads is forced against the inner and outer surfaces of the steel brake rotor under tremendous pressure. The resulting friction causes the wheels on your car to slow rapidly allowing for a quick, safe and controlled stop. After thousands of miles, this friction material eventually wears away, and the brake rotor wears away as well, requiring replacement.

Brakes-Service

When to replace brake pads?

Here are several indications that you need new brake pads:

  • Wear indicator on vehicle dashboard. When the friction material on the brake pads is worn to within 2 mm of the pad backing plate, replacement of the pads is necessary. Most newer cars today have electronics built into the brake pad. When the pad is at a point that it needs to be replaced, a symbol will appear on your vehicle dashboard’s instrument cluster. Consult your owner’s manual to learn what the symbol looks like.
  • High pitched squeal when braking. When the friction material on the pads is worn close to the backing plate, you may hear a squealing or squeaking noise as you drive regardless of whether you are applying the brakes or not. That squealing or squeaking noise is designed to make you aware that the brake pads are getting low and need to be inspected. If all of the friction material on the brake pad has been worn away, you will hear grinding and scraping noises when you apply the brakes. Pad replacement is mandatory at this point and the vehicle is unsafe to drive until corrected.
  • Brake pedal pulsation or vehicle vibration. Over time, brake rotors may develop excessive thickness variation (>.001 inches), excessive runout on the wheel hub (> .002 inches), or the brake rotor may warp due to high operating temperatures. If these defects exist, you may notice pulsation in the brake pedal or steering wheel during braking. New pads and rotor resurfacing or replacement will be required if the rotor has any of the above-mentioned deficiencies.
  • Vehicle pulling or wandering on braking. If your car pulls to the right or left during braking, that could be a sign of a sticking brake caliper, misalignment of the suspension, and sometimes tire defects or uneven tire inflation from side-to-side. The mechanic who inspects your vehicle will determine if new brake pads alone will resolve the issue or if other repairs are needed.
  • High mileage on existing pads. Regardless of whether any of the above brake system symptoms occur, every 10,000 miles a mechanic should measure the thickness of the remaining friction material on the brake pads and perform a thorough visual inspection of the braking system.
  • Brake system warning lights and/or maintenance reminder messages. Should your brake system warning light ever illuminates, or a brake system related maintenance reminder message appears in the driver information display, have your vehicle inspected and repaired as soon as possible.

How do mechanics replace brake pads?

Normally, pad replacement requires these steps:

  • Confirm the thickness of the remaining friction material on the brake pads. If the remaining friction material is less than 2 mm in thickness, pad replacement is warranted.
  • Visually inspect the brake rotor surface that contacts the pad (for scoring, pitting, grooves, rust) and measure the brake rotor with precision tools for thickness variation, run-out and warpage.
  • Inspect the caliper, torque plate, pads, and rotors to determine if the caliper is operating freely (i.e., inspect for stuck calipers).
  • Install new pads and any additional recommended components (e.g., rotors, if rotors depart from OEM specifications) only with customer approval of course.
  • Lubricate brake system components, such as caliper sliding pins, and inspect the condition of the brake fluid. Top off brake fluid as required.
  • Perform a basic 50 point safety inspection of your vehicle.
  • Finally, the mechanic will test drive your vehicle to confirm normal operation of the brake system.

Is it safe to drive with a brake pad problem?

Driving a vehicle with a known deficiency in the braking system is unsafe and consequently is not recommended. Worn out brake pads can increase stopping distances and so for your safety, it is always advised that worn out brake pads be replaced promptly. Further driving is not recommended and you should request service at your earliest convenience if any of the following circumstances exist: stopping distances are much greater than what you are accustomed to; the brake pedal is not firm or is low; there is loss of braking power assist; the vehicle pulls severely to one side on braking; or the brake system warning light is on.

If you detect unusual noises, such as squealing or grinding, but stopping distances are close to what you are used to, and the brake pedal is firm, and there are no warning lights, it may be safe to proceed to your destination but schedule service at your earliest convenience. When it comes to the brakes on your vehicle, always err on the side of caution and have a mechanic check your brake pads and braking system at the first indication of a problem.

When replacing brake pads keep in mind:

Brake pads must always be replaced as a set, that is both wheels (driver and passenger side) on an axle, front or rear, must be serviced. If brake pads on only one side of the car were replaced, your car might pull to one side when you apply the brakes. Often, resurfacing or replacement of the brake rotors is necessary and a competent mechanic will always measure for wear and damage to the brake rotors and advise you as to whether rotor replacement or re-surfacing is needed.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(17)

Rating Summary
16
0
0
0
1
16
0
0
0
1

Richard

11 years of experience
450 reviews
Richard
11 years of experience
Mercedes-Benz CLK550 V8-5.5L - 75 Point Safety Inspection - Spring, Texas
Very knowledgeable, personable and professional.

Sayeed

17 years of experience
82 reviews
Sayeed
17 years of experience
Mercedes-Benz CLK550 V8-5.5L - Coolant Reservoir - Westbury, New York
Great experience. Saeed was on time, he is very knowledgeable. He was able to fix the problem the same day. I will definitely use him again!

Ben

41 years of experience
1410 reviews
Ben
41 years of experience
Mercedes-Benz CLK550 V8-5.5L - Pre-purchase Car Inspection - Houston, Texas

Damian

11 years of experience
465 reviews
Damian
11 years of experience
Mercedes-Benz CLK550 V8-5.5L - Control Arm Assembly Replacement (Front Upper Right, Front Lower Right) - Bowie, Maryland
Very prompt and professional. Knowledge of my car, identified the repair immediately.

Excellent Rating

(17)

Rating Summary
16
0
0
0
1
16
0
0
0
1
Number of Mercedes-Benz CLK550 services completed
187+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

P0048 OBD-II Trouble Code: Turbo/Super Charger Boost Control Solenoid Circuit High
P0048 P0048 Trouble Code definition Turbo/Super Charger Boost Control Solenoid Circuit High What the P0048 code means This code has varied definitions as provided by the manufacturer. The code means that the ECU (Engine Control Unit) has detected an out...
P2264 OBD-II Trouble Code: Water in Fuel Sensor Circuit
P2264 P2264 code definition Water in Fuel Sensor Circuit What the P2264 code means P2264 is an OBD-II generic code for the engine control module (ECM) detecting the water in fuel sensor circuit voltage falling below or exceeding the specified...
P0492 OBD-II Trouble Code: Secondary Air Injection System Insufficient Flow Bank
P0492 means there is a problem with the secondary air injection system, often due to intake leaks or faulty one-way check valves.

Car cranking without key in ignition

This is usually a sign of a faulty starter solenoid. There are a few wires that connect to the starter solenoid coming from the battery, the starter, and the ignition switch. When these wires are connected incorrectly or when there...

Slave cylinder for clutch

The clutch slave cylinder is external outside the transmission. It can be replaced without removing the transmission.

2014 Ford Focus Blower Resistor Location

If you have Electronic Manual Temperature Control (EMTC), the blower motor resistor block is accessed by removing the accelerator pedal. Once the pedal is removed you will see the wiring harness to the block and the single retaining screw that...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com