Mercedes-Benz 400SE Intake Manifold Gaskets Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(13)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(13)

Intake Manifold Gaskets Replacement Service

How much does a Intake Manifold Gaskets Replacement cost?

On average, the cost for a Mercedes-Benz 400SE Intake Manifold Gaskets Replacement is $766 with $122 for parts and $644 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1992 Mercedes-Benz 400SEV8-4.2LService typeIntake Manifold Gaskets ReplacementEstimate$956.90Shop/Dealer Price$1046.86 - $1251.52
Show example Mercedes-Benz 400SE Intake Manifold Gaskets Replacement prices

What is an intake manifold gasket and how does it work?

The intake on an engine may be made up of a lower intake manifold and an upper intake manifold or plenum. The lower intake manifold is a cast aluminum or molded plastic chamber bolted to the cylinder head of the engine. The intake manifold must be tightly sealed to the cylinder head(s) using a gasket in order to prevent air, oil, or engine coolant leaks.

When to consider replacing the intake manifold gasket:

Internal or external leaks. Due to constant temperature expansion and contraction of engine parts or overheating, the gasket’s ability to seal properly can be ruined, resulting in problems such as:

  • Internal or external engine coolant leaks. In some applications, the manifold has cooling passages within. If the manifold seal to the engine fails, coolant can leak externally or even into the engine oil crankcase, where coolant can be noticed in the engine oil.
  • Engine overheating. If the leak at the manifold is a leak of engine coolant, it can lead to engine overheating. However, there are other causes of engine overheating, so a mechanic would have to determine the actual cause.
  • External oil leaks. On some 6 and 8 cylinder engines, the intake manifold sits atop an oil-lubricated area of the engine block. If the manifold gasket has failed, oil can leak from the block to the exterior of the engine.
  • Poor engine operation, lean operation, rough idle. Vacuum air leaks into the manifold due to a defective gasket that will upset the air-fuel ratio. The engine may run poorly.
  • Check engine light. Minor leaks at the intake manifold gasket will not usually cause the check engine light to illuminate. However, as a leak persists, it may grow larger and it possible for the leak to degrade engine performance enough that it will cause a trouble code to set, which will cause the check engine light to illuminate.

How do mechanics replace the intake manifold gasket?

  • Working on a cold engine, the engine cover is removed. If the intake manifold has internal cooling system passageways, the engine coolant is drained below the level of those passageways.
  • The accelerator cable assembly and cruise control cable are removed and set aside. All electrical connections and emission and vacuum lines in the way of the intake are removed. Ignition components, such as the coil, are removed as needed. If the car has an upper plenum, that is removed and set aside.
  • If the fuel rail is bolted to the intake manifold, the supply and return connections to the fuel rail are disconnected.
  • Once all connections to the manifold are clear, the manifold is unbolted and removed from the engine.
  • Aluminum and plastic manifolds are checked with a machinist’s straightedge to ensure the surface flatness does not exceed the original equipment manufacturer’s specification. If the surface of a manifold is not flat, the new gasket will not seal properly. Plastic manifolds are checked for cracks, heat damage, and warpage.
  • Once the manifold is deemed re-usable or replaced as needed, the new gasket is applied, the manifold is put in position and the mounting bolts are torqued with a calibrated torque wrench in the OEM specified sequence. In some applications, RTV sealant must be applied in corners of the mounting surface or specified hard-to-seal spots, per the service manual.
  • All removed components are then re-installed in the reverse of the above steps.
  • Finally, the vehicle is run and checked for leaks, and test driven.

Is it safe to drive with an intake manifold gasket problem?

Yes. The principal concern with a leaking intake manifold gasket is potential damage to the engine, depending on where the leak is. Although the vehicle will generally be safe to drive, you should schedule service as soon as possible to minimize the chances of additional costly damage. If the leak involves coolant, it could lead to engine overheating damage or the coolant could contaminate the engine oil, which can damage the engine bearings. If there is an air leak to the cylinders, it can cause lean operation which could overheat the catalytic converter.

When replacing the intake manifold gasket keep in mind:

  • In engines where coolant flows through the intake manifold, a leaking intake manifold gasket can be either the cause of or result of engine overheating. If you have a leaking intake manifold gasket, and the engine has overheated, the entire engine should be inspected for damage, such as a blown head gasket. The engine cooling system thermostat should be replaced because engine overheating can damage the cooling system thermostat.
  • Some car engine designs are more likely than others to experience leaking intake manifold gaskets due to material and design issues. Your mechanic can inform you if your car represents one of these cases. Many times a re-designed gasket, or altered installation technique and torque values, will be relevant to avoid a recurrence of any leaks. Mechanics will consult Technical Service Bulletins to determine if any unique circumstance exists for your car.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(13)

Rating Summary
10
1
0
0
2
10
1
0
0
2

James

31 years of experience
1039 reviews
James
31 years of experience
Mercedes-Benz C300 V6-3.0L - Intake Manifold Gaskets - Orlando, Florida
Very good mechanic!! I really appreciate James for replacing my intake manifold gasket. He was very friendly and make sure he did he's job before he left.

Patrick

34 years of experience
1579 reviews
Patrick
34 years of experience
Mercedes-Benz E500 V8-5.0L - Intake Manifold Gaskets - Austin, Texas
On time, went out of his way to help, excellent service , will use again !!!

Jason

33 years of experience
617 reviews
Jason
33 years of experience
Mercedes-Benz R350 V6-3.5L - Intake Manifold Gaskets - Rowlett, Texas
Jason is just the bees knees! He was much faster than the estimated time and was so thoughtful throughout the fix. He allowed me to learn how to maintain my car alongside his service repairs -- that is a unique blessing for any mechanic I've ever experienced. He also has a laugh like Seth Rogan so he brings a great sense of humor to the job. If you stay or leave for your repairs, you can be assured that Jason will be speedy, knowledgeable, and thoughtful during your time. I recommend him majorly!

Eric

15 years of experience
73 reviews
Eric
15 years of experience
Mercedes-Benz C230 L4-1.8L Turbo - Intake Manifold Gaskets - Jonesboro, Georgia
Experience was great but he only replaced the tensioner and serpentine belt not the intake manifold gasket...but he did a great job

Excellent Rating

(13)

Rating Summary
10
1
0
0
2
10
1
0
0
2
Number of Mercedes-Benz Intake Manifold Gaskets Replacement services completed
143+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

P0767 OBD-II Trouble Code: Shift Solenoid D Stuck On
P0767 code means there is an abnormality detected in shift solenoid "D" often due too transmission blockages or low/dirty fluids.
P0580 OBD-II Trouble Code: Cruise control Multi-Function Input "A" Circuit Low
P0580 P0580 OBD-II Trouble Code: Cruise control Multi-Function Input "A" Circuit Low Diagnostic Trouble Code (DTC): P0580 P0580 code definition A P0580 code means that the PCM has found an electrical problem with the multi-function input circuit in the vehicle’s...
The Guide To Colored Curb Zones in Connecticut
Connecticut Connecticut parking laws and colored pavement markings While there are certainly plenty of rules and laws to remember when you are behind the wheel and on the road in Connecticut, you also have to keep in mind the parking...

What causes the car to shake when the AC is on?

The a/c compressor will start to put a larger strain on the engine if the pressures rise above 400 psi. This can happen if there is a problem with the a/c cooling fans or the a/c system has a restriction...

My new front brake pads and rotors are making noise

Hello. Organic brake pads have a reputation for being quiet most of the time. Most of the complaints come from squeaks when the pads are wet. You describe your symptoms as more of a grinding, metal on metal, type of...

Fuel tank filler neck assembly leaking. Sensor code P0442

I am working on this

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com