Mercedes-Benz 400E Front Crankshaft Seal Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(3)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(3)

Front Crankshaft Seal Replacement Service

How much does a Front Crankshaft Seal Replacement cost?

On average, the cost for a Mercedes-Benz 400E Front Crankshaft Seal Replacement is $507 with $17 for parts and $490 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1992 Mercedes-Benz 400EV8-4.2LService typeFront Crankshaft Seal ReplacementEstimate$576.48Shop/Dealer Price$607.03 - $649.05
1993 Mercedes-Benz 400EV8-4.2LService typeFront Crankshaft Seal ReplacementEstimate$544.95Shop/Dealer Price$564.67 - $598.58
Show example Mercedes-Benz 400E Front Crankshaft Seal Replacement prices

What is the Front Crankshaft Seal all about?

A number of mechanisms must work together to make your vehicle move forward. One of the most important is the crankshaft, which converts rotary into linear motion; i.e., it transforms the force created by the engine's pistons moving up and down into a force that moves in a circular motion that causes a car’s wheel to turn. Enclosed in what’s called a crankcase—the largest cavity in the engine block, just below the cylinders—the crankshaft must be completely lubricated, essentially submerged in oil, to spin nearly friction-free and do its job properly.

Consequently, there are seals located at either end of the crankshaft that allow it to spin freely and keep engine oil from escaping the engine block, as well as prevent contaminants and other debris from entering and causing damage to the mechanism. Since there are two ends of the crankshaft, there are two types of seals: the front crankshaft seal and the rear crankshaft seal, also known as the front main and rear main seals.

Keep in mind:

  • Loss of oil will eventually cause serious internal engine damage.
  • Inspect the sealing surface of the crankshaft or the crankshaft pulley (depending on the engine design) for damage when replacing the crankshaft seal.
  • Oil degrades rubber components.

How it's done:

  • The vehicle is raised and supported on jack stands
  • The crankshaft damper and timing belt is removed
  • The crankshaft seal is removed and a new one installed
  • The timing belt and cover along with crankshaft damper is reinstalled
  • The engine accessory belts are installed and the vehicle is lowered off of the jack stands

Our recommendation:

One of the most important parts of your car, crankshaft seals are typically made from a durable material, such as a synthetic rubber or silicone, designed to handle the extreme pressure and temperatures as well as the caustic chemicals in your engine oil. Because they are exposed to such abuse, main seals are subject to a lot of wear and tear. And whether you are talking a front or rear main seal, replacement is the only cure when one malfunctions.

The good news is that the seals are relatively inexpensive components. The bad news is that neither is easy to replace.

Front seal: The front seal is located behind the main pulley that drives all the belts, which is, of course, always spinning. The main pulley throws any leaking oil out in a big circle. It can get thrown up on the alternator, steering pump, belts, in short anything attached to the front of the engine and cause a real mess and eventually some serious damage. Consequently, it has to be removed along with many of the components attached to the front of the block to replace the front main seal.

Rear seal: The rear crankshaft seal is placed along with the transmission; therefore, the process of replacing it requires the removal of transmission, as well as the clutch and flywheel assembly. This is a very involved job.

What common symptoms indicate you may need to replace the Front Crankshaft Seal?

  • Oil leaking from the front crank pulley.
  • Oil dripping from the bottom of the clutch housing, where the block and transmission meet.
  • Clutch slip caused by oil spraying on the clutch.

How important is this service?

Letting either crankshaft seal continue to leak can be detrimental to your vehicle’s continued operation. Besides the maladies caused by driving around with little to no oil flowing in the engine, the faulty seal will be spread oil through the engine bay and undercarriage of your car as you drive, a mess that is difficult to clean up and can be a fire hazard. Replacing is better addressed sooner than later.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(3)

Rating Summary
3
0
0
0
0
3
0
0
0
0

Ryan

6 years of experience
61 reviews
Ryan
6 years of experience
Mercedes-Benz 400E V8-4.2L - Power Steering Pump - Phoenix, Arizona
ryan was good but you service was nasty ,and i will never used you all again. I was a good customer and i spend money with you for over 3 years and i never thought i would get that kind of service..

Ryan

23 years of experience
85 reviews
Ryan
23 years of experience
Mercedes-Benz 400E V8-4.2L - Oil Pressure Sensor - Huntersville, North Carolina
Very upfront

Rohon

49 years of experience
147 reviews
Rohon
49 years of experience
Mercedes-Benz C250 L4-1.8L Turbo - Front Crankshaft Seal - Jupiter, Florida
Rohan went above and beyond what was required of his work. He was punctual, professional, cordial, and is the type of person you want around for a bbq or to hang out with. His years of service and knowledge is reflected in the quality of his workmanship. And my go to mechanic from here on.

Ben

26 years of experience
22 reviews
Ben
26 years of experience
Mercedes-Benz C230 V6-2.5L - Front Crankshaft Seal Replacement - Norman, Oklahoma
Ben was great. Showed up on time, brought all the tools he needed for a fairly involved job, even custom made a tool, and thoroughly cleaned up the area when finished. He was very knowledgeable about the job at hand, completed it efficiently, and did not try to up-sell any additional service. The price paid was exactly as quoted even though it was a more involved fix than estimated. Very impressed with Ben and the service.

Excellent Rating

(3)

Rating Summary
3
0
0
0
0
3
0
0
0
0
Number of Mercedes-Benz Front Crankshaft Seal Replacement services completed
33+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

P2007 OBD-II Trouble Code: Intake Manifold Runner Control Stuck Closed Bank 2
P2007 P2007 trouble code definition P2007 is a general OBD2 code that indicates a malfunction in the intake manifold runner control circuit. This code is similar to P2004, P2005, P2006, P2008, P2009, P2010 and P2015. What the P2007 code means...
Rhode Island Parking Laws: Understanding the Basics
Drivers Drivers in Rhode Island need to be aware of the parking laws in their state and community. Failure to abide by the parking laws could mean fines, and it could mean your vehicle being towed to the impound yard....
How Long Does a Power Window Switch Last?
Power Power windows are definitely convenient, particularly with the auto up and down functionality that’s now present in many newer cars. It sure beats having to manually roll the window up or down when you need to get some fresh...

Passenger's side window not going up or down.

Hi. All of the power windows are supplied power via the same fuse so if all the other windows windows operate, then the problem lies in the right front door. The door panel will need to be removed to diagnose...

Digital dashboard not working

Hello! That is a common problem that unfortunately usually requires a replacement of the instrument cluster. The clusters will short out internally over time, due to faulty solder points. The solder points will usually fail due to the heat those...

Jerking reaction when accelerating

This may be a couple of different things. When a transmission is low on fluid, this can cause a jerking reaction as you describe. Automatic transmissions use pressurized hydraulic fluid to change gears. Every time a gear change is required,...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com