Hyundai Equus Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(28)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(28)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Hyundai Equus Tie Rod End Replacement is $159 with $64 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2011 Hyundai EquusV8-4.6LService typeTie Rod End - Rear Right Outer ReplacementEstimate$364.65Shop/Dealer Price$437.07 - $631.81
2012 Hyundai EquusV8-5.0LService typeTie Rod End - Rear Right Outer ReplacementEstimate$344.65Shop/Dealer Price$417.08 - $611.84
2015 Hyundai EquusV8-5.0LService typeTie Rod End - Front Left Outer ReplacementEstimate$223.65Shop/Dealer Price$265.83 - $369.84
2015 Hyundai EquusV8-5.0LService typeTie Rod End - Front Right Inner ReplacementEstimate$385.94Shop/Dealer Price$448.04 - $578.12
2012 Hyundai EquusV8-5.0LService typeTie Rod End - Front Left Inner ReplacementEstimate$385.94Shop/Dealer Price$448.13 - $578.29
2011 Hyundai EquusV8-4.6LService typeTie Rod End - Front Right Inner ReplacementEstimate$385.94Shop/Dealer Price$448.09 - $578.22
2011 Hyundai EquusV8-4.6LService typeTie Rod End - Front Left Inner ReplacementEstimate$398.44Shop/Dealer Price$460.25 - $590.13
2016 Hyundai EquusV8-5.0LService typeTie Rod End - Front Right Outer ReplacementEstimate$228.65Shop/Dealer Price$271.07 - $375.26
Show example Hyundai Equus Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Hyundai mechanics

Real customer reviews from Hyundai owners like you.

Excellent Rating

(28)

Rating Summary
27
1
0
0
0
27
1
0
0
0

Omar

12 years of experience
287 reviews
Omar
12 years of experience
Hyundai Equus V8-5.0L - Alternator Repair - Pompano Beach, Florida
Awesome, knowledgeable, wasn't afraid of a challenge, would recommend to anyone for any car.

Jeremy

20 years of experience
603 reviews
Jeremy
20 years of experience
Hyundai Equus V8-5.0L - Battery - Delray Beach, Florida
Excellent service

Corey

17 years of experience
341 reviews
Corey
17 years of experience
Hyundai Equus V8-5.0L - Suspension Air Bag Replacement (Driver Side Rear, Passenger Side Rear) - Charlotte, North Carolina
Very knowledgeable and professional will use him always!!

Mathew

17 years of experience
66 reviews
Mathew
17 years of experience
Hyundai Equus V8-5.0L - Car Battery Replacement - Brooksville, Florida
Good profesional

Excellent Rating

(28)

Rating Summary
27
1
0
0
0
27
1
0
0
0
Number of Hyundai Equus services completed
308+
services done by our mechanics
TOTAL NUMBER OF EXPERT Hyundai MECHANICS
1300+
experts on our platform

Recent articles & questions

The Traveler’s Guide to Driving in Belgium
Belgium Belgium is a beautiful, historic city that has a lot to offer those who vacation there. You may want to spend some time exploring Brussels and visiting places (https://www.tripadvisor.com/Attractions-g188634-Activities-Belgium.html) such as the Grand Palace. You may also want to...
P2723 OBD-II Trouble Code: Clutch Pressure Control Solenoid 5 - Stuck Off
P2723 means a solenoid has malfunctioned due to low fluid levels, a failing transmission, faulty sensor or solenoid, or electrical issues or problems.
Understanding the Smart Car Service Interval Indicator System
Car symbols, or dashboard lights, are a car service reminder. The Smart Car Service Interval Indicator System tells you when your car needs service.

Toyota RAV4 front right tire hit curb hard. Tire popped, rim damaged

Hi there. Prior to knowing what it may cost to repair your vehicle the suspension will need to be fully inspected. Many of the parts may be broken or bent so they will all need to be assessed for safety....

Backfiring and sluggish

It sounds like you may have a misfire or a timing problem causing the motor to backfire. Engine misfires can be caused by many different problems and are generally caused by either a spark or fuel issue or in some...

Belt tensioner broke 2006 Cadillac DTS

Hello - yes, the serpentine belt (aka accessory drive belt) drives your water pump as well as the alternator, power steering pump, etc. Failure of the belt or tensioner (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-drive-belt-tensioner) means hot water in the engine is not pumped to...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com