Honda CRX Fuel Injector Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(16)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(16)

Fuel Injector Replacement Service

How much does a Fuel Injector Replacement cost?

On average, the cost for a Honda CRX Fuel Injector Replacement is $515 with $375 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1990 Honda CRXL4-1.6LService typeFuel Injector ReplacementEstimate$905.26Shop/Dealer Price$1096.43 - $1661.82
1991 Honda CRXL4-1.6LService typeFuel Injector ReplacementEstimate$896.25Shop/Dealer Price$1085.65 - $1649.72
1990 Honda CRXL4-1.5LService typeFuel Injector ReplacementEstimate$1241.85Shop/Dealer Price$1517.67 - $2340.96
1991 Honda CRXL4-1.5LService typeFuel Injector ReplacementEstimate$1241.85Shop/Dealer Price$1517.67 - $2340.96
Show example Honda CRX Fuel Injector Replacement prices

What is a fuel injector and how does it work?

A fuel injector is a fuel metering device that sprays atomized droplets of fuel in a specific pattern into the engine’s intake manifold or directly into the combustion chamber. The injector has a solenoid and valve within and the operation, or pulsing, of the solenoid is controlled by the powertrain control module (PCM). The PCM controls the solenoid’s “on” time in order to keep the air-fuel ratio optimized while the engine load and operating conditions constantly change. Fuel injectors are usually connected to a fuel rail located on the top of the engine and the fuel rail, in turn, is supplied with fuel under pressure from the fuel pump located in the fuel tank.

When to consider replacing a fuel injector:

  • Rough idle, loss of power, or misfiring. Poor engine operation has many causes but faults in the fuel injection system, including the fuel injectors, are high on the list of possibilities.
  • Odor of raw gas or visible leaks. Fuel injectors should not leak fuel into the intake manifold when the car is off. If you notice any fuel odor around your car, the possibility of a leaking fuel injector should be considered. There should be no external leak from a fuel injector. If an externally-leaking injector is suspected, do not start your car due to the fire hazard.
  • Check engine light. Some fuel injection failures, for example, a faulty solenoid, may cause a trouble code to be set in the PCM and that will cause the check engine light to illuminate. The codes are read and the fuel injector is tested directly, as needed.
  • Major engine repairs, engine replacement, or lengthy storage. All fuel injectors will have deposits given enough mileage. These deposits can cause an imbalance in the performance of the injectors from cylinder to cylinder. When an engine is already disassembled, or if you are installing a new engine, that is a perfect time to service the injectors as a set. All injectors have tiny internal filter baskets. A professional injector service facility will clean each injector ultrasonically and replace these filters for a relatively low cost.

How do mechanics replace a fuel injector?

Injectors can be serviced once removed from the car or replaced outright with new injectors. If the injectors are serviced, specialized cleaning and test equipment are required. The choice to repair versus replace will depend on exactly what is wrong with the injector as well as customer preference. Either option requires removing the injector from the car and the following procedure is typical:

  • Once the engine is cold, the pressure within the fuel rail is relieved by briefly running the engine with the fuel pump fuse out.
  • The upper plenum on the intake manifold is removed along with any cables, hoses, or wiring that restricts access.
  • The supply and return lines are removed from the fuel rail. The electrical connectors to each fuel injector are unlocked and removed. The fuel rail is then unbolted and removed from the intake manifold.
  • The injector(s) requiring replacement are removed from the fuel rail, taking care to not allow any debris to enter the exposed openings. An O-ring seal usually holds the injector very firmly in a finely polished bore in the fuel rail.
  • Using a new O-ring, the serviced or replaced injector is re-inserted into the fuel rail — using engine oil on the O-ring to prevent damaging it. O-rings in this application fit very tight to prevent fuel leaks.
  • The fuel rail is re-installed and the supply and return lines are re-connected. The plenum is re-installed along with all cables, hoses, or wiring.
  • Finally, the engine is run, there is a careful check for leaks, and the vehicle is road tested.

Is it safe to drive with a fuel injector problem?

Yes, so long as there is no external leak of fuel from a broken or malfunctioning injector, it is safe to drive the car. However, if the injector is known to be malfunctioning, it can cause engine misfires, excessive emissions or, in the case of a badly leaking injector, can overload and overheat the catalytic converter. Additionally, fuel efficiency will always be diminished if the fuel injectors are not working properly.

When replacing a fuel injector keep in mind:

  • Using high quality (Tier One) gasoline may reduce deposits on fuel injectors and prolong their life.
  • If an injector problem develops that requires removal of one injector, the best practice is to remove and service all of the injectors at the same time. That service might involve replacement of the electrically failed injector along with off-the-car cleaning of the remaining injectors. Serving all injectors at once ensures the injector set will be balanced, in terms of flow rates, and in turn promote smooth operation of the engine.
  • Do not use fuel system cleaning compounds, or procedures, unless such materials are specified by the manufacturer of your car.
  • On the car cleaning of fuel injectors is not as effective as off-the-car cleaning because injectors have tiny internal filter baskets that should be replaced as part of the process of servicing a fuel injector.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Honda mechanics

Real customer reviews from Honda owners like you.

Excellent Rating

(16)

Rating Summary
14
1
0
0
1
14
1
0
0
1

Manuel

33 years of experience
590 reviews
Manuel
33 years of experience
Honda CRX L4-1.6L - Radiator - Foothill Ranch, California
Very satisfied customer.

Jamahl

21 years of experience
830 reviews
Jamahl
21 years of experience
Honda CRX L4-1.5L - Brake Caliper Replacement (Passenger Side Front) - Gotha, Florida

Joshua

28 years of experience
709 reviews
Joshua
28 years of experience
Honda CRX L4-1.5L - Cooling System Flush - Antioch, California
Joshua did a great job. He quickly found the issue. Total cost was actually less than the original quote.

James

32 years of experience
705 reviews
James
32 years of experience
Honda CRX L4-1.6L - Fan speed control is not working - Yorba Linda, California
On time and quick to find the problem

Excellent Rating

(16)

Rating Summary
14
1
0
0
1
14
1
0
0
1
Number of Honda CRX services completed
176+
services done by our mechanics
TOTAL NUMBER OF EXPERT Honda MECHANICS
1700+
experts on our platform

Recent articles & questions

How to Get Smog Technician Certified in Idaho
Automotive technician jobs include smog certified emissions inspectors. In Idaho, how to become an inspector varies by county.
How to Port and Polish Your Car Cylinder Heads
Engine performance increases when you port and polish the cylinder heads in your car. Save money by doing the job yourself instead of a shop.
5 Essential Things to Know About Road Rage
Road rage goes beyond aggressive driving as the driver either tries to or is successful at causing harm to another driver on the road.

My front brake calipers are sticking and not releasing

Lift up the front wheels to where they are off the ground. Remove the wheels and tires from the vehicle on the front. Remove the slider bolts one at a time and clean them. Apply Never Seize to the sliding...

Why does my car struggle on any hill or highway ? It will not go above 30 mph and feels like it won't go above 2nd gear 2008 Kia Sportage

Hello - the loss of power (https://www.yourmechanic.com/question/suv-experienced-low-acceleration-and-loss-of-power) you are experiencing could be a failed throttle position sensor, or a clogged catalytic converter. Either of these will reduce engine power, and cause the lack of performance you are seeing. I recommend...

Tire blow out and it ripped the wire harness. I replaced the harness and spliced wires but it won't turn over

Check the wiring to what it went to. If the wiring went to a sensor, then check the sensor to see if it was damaged. If the engine is not starting, then the crankshaft sensor could have been damaged. If...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com