Geo Tracker Brake Pad Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(15)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(15)

Brake Pad Replacement Service

How much does a Brake Pad Replacement cost?

On average, the cost for a Geo Tracker Brake Pad Replacement is $196 with $56 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1992 Geo TrackerL4-1.6LService typeBrake Pads - Front ReplacementEstimate$316.12Shop/Dealer Price$360.00 - $483.54
1996 Geo TrackerL4-1.6LService typeBrake Pads - Front ReplacementEstimate$307.11Shop/Dealer Price$349.22 - $471.44
1990 Geo TrackerL4-1.6LService typeBrake Pads - Front ReplacementEstimate$307.11Shop/Dealer Price$349.25 - $471.48
1995 Geo TrackerL4-1.6LService typeBrake Pads - Rear ReplacementEstimate$344.33Shop/Dealer Price$378.45 - $474.54
1995 Geo TrackerL4-1.6LService typeBrake Pads - Front ReplacementEstimate$332.63Shop/Dealer Price$382.62 - $525.10
1990 Geo TrackerL4-1.6LService typeBrake Pads - Rear ReplacementEstimate$340.79Shop/Dealer Price$374.23 - $467.83
1997 Geo TrackerL4-1.6LService typeBrake Pads - Rear ReplacementEstimate$344.33Shop/Dealer Price$378.47 - $474.58
1993 Geo TrackerL4-1.6LService typeBrake Pads - Rear ReplacementEstimate$344.33Shop/Dealer Price$378.45 - $474.54
Show example Geo Tracker Brake Pad Replacement prices

What are brake pads and how do they work?

Brake pads consist of friction material that is bonded to a sturdy steel backing plate. When you push on the brake pedal, the friction material on the brake pads is forced against the inner and outer surfaces of the steel brake rotor under tremendous pressure. The resulting friction causes the wheels on your car to slow rapidly allowing for a quick, safe and controlled stop. After thousands of miles, this friction material eventually wears away, and the brake rotor wears away as well, requiring replacement.

Brakes-Service

When to replace brake pads?

Here are several indications that you need new brake pads:

  • Wear indicator on vehicle dashboard. When the friction material on the brake pads is worn to within 2 mm of the pad backing plate, replacement of the pads is necessary. Most newer cars today have electronics built into the brake pad. When the pad is at a point that it needs to be replaced, a symbol will appear on your vehicle dashboard’s instrument cluster. Consult your owner’s manual to learn what the symbol looks like.
  • High pitched squeal when braking. When the friction material on the pads is worn close to the backing plate, you may hear a squealing or squeaking noise as you drive regardless of whether you are applying the brakes or not. That squealing or squeaking noise is designed to make you aware that the brake pads are getting low and need to be inspected. If all of the friction material on the brake pad has been worn away, you will hear grinding and scraping noises when you apply the brakes. Pad replacement is mandatory at this point and the vehicle is unsafe to drive until corrected.
  • Brake pedal pulsation or vehicle vibration. Over time, brake rotors may develop excessive thickness variation (>.001 inches), excessive runout on the wheel hub (> .002 inches), or the brake rotor may warp due to high operating temperatures. If these defects exist, you may notice pulsation in the brake pedal or steering wheel during braking. New pads and rotor resurfacing or replacement will be required if the rotor has any of the above-mentioned deficiencies.
  • Vehicle pulling or wandering on braking. If your car pulls to the right or left during braking, that could be a sign of a sticking brake caliper, misalignment of the suspension, and sometimes tire defects or uneven tire inflation from side-to-side. The mechanic who inspects your vehicle will determine if new brake pads alone will resolve the issue or if other repairs are needed.
  • High mileage on existing pads. Regardless of whether any of the above brake system symptoms occur, every 10,000 miles a mechanic should measure the thickness of the remaining friction material on the brake pads and perform a thorough visual inspection of the braking system.
  • Brake system warning lights and/or maintenance reminder messages. Should your brake system warning light ever illuminates, or a brake system related maintenance reminder message appears in the driver information display, have your vehicle inspected and repaired as soon as possible.

How do mechanics replace brake pads?

Normally, pad replacement requires these steps:

  • Confirm the thickness of the remaining friction material on the brake pads. If the remaining friction material is less than 2 mm in thickness, pad replacement is warranted.
  • Visually inspect the brake rotor surface that contacts the pad (for scoring, pitting, grooves, rust) and measure the brake rotor with precision tools for thickness variation, run-out and warpage.
  • Inspect the caliper, torque plate, pads, and rotors to determine if the caliper is operating freely (i.e., inspect for stuck calipers).
  • Install new pads and any additional recommended components (e.g., rotors, if rotors depart from OEM specifications) only with customer approval of course.
  • Lubricate brake system components, such as caliper sliding pins, and inspect the condition of the brake fluid. Top off brake fluid as required.
  • Perform a basic 50 point safety inspection of your vehicle.
  • Finally, the mechanic will test drive your vehicle to confirm normal operation of the brake system.

Is it safe to drive with a brake pad problem?

Driving a vehicle with a known deficiency in the braking system is unsafe and consequently is not recommended. Worn out brake pads can increase stopping distances and so for your safety, it is always advised that worn out brake pads be replaced promptly. Further driving is not recommended and you should request service at your earliest convenience if any of the following circumstances exist: stopping distances are much greater than what you are accustomed to; the brake pedal is not firm or is low; there is loss of braking power assist; the vehicle pulls severely to one side on braking; or the brake system warning light is on.

If you detect unusual noises, such as squealing or grinding, but stopping distances are close to what you are used to, and the brake pedal is firm, and there are no warning lights, it may be safe to proceed to your destination but schedule service at your earliest convenience. When it comes to the brakes on your vehicle, always err on the side of caution and have a mechanic check your brake pads and braking system at the first indication of a problem.

When replacing brake pads keep in mind:

Brake pads must always be replaced as a set, that is both wheels (driver and passenger side) on an axle, front or rear, must be serviced. If brake pads on only one side of the car were replaced, your car might pull to one side when you apply the brakes. Often, resurfacing or replacement of the brake rotors is necessary and a competent mechanic will always measure for wear and damage to the brake rotors and advise you as to whether rotor replacement or re-surfacing is needed.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Geo mechanics

Real customer reviews from Geo owners like you.

Excellent Rating

(15)

Rating Summary
14
1
0
0
0
14
1
0
0
0

Jeffrey

28 years of experience
870 reviews
Jeffrey
28 years of experience
Geo Tracker L4-1.6L - Valve Cover Gasket - Catawba, South Carolina
Jeffery was actually early for my appointment, which i had had to reschedule and he was very understanding of the reason for my reschedule and i appreciated him getting to my home earlier than scheduled. Jeffery was very knowledgeable about my repair work and preformed the work promptly. his inspection and evaluation of my car was also helpful since it has some miles on it. Great effort.

Duane

26 years of experience
589 reviews
Duane
26 years of experience
Geo Tracker L4-1.6L - Car AC Repair - San Diego, California
Duane is a real professional. It's a real relief when you know a pro is taking care of your ride. Thanks, Duane!

Tung

17 years of experience
310 reviews
Tung
17 years of experience
Geo Tracker L4-1.6L - Starter - Atlanta, Georgia
The experience was good and Tung completed the ticket based on the expected part installs. But the truck is coughing and sputtering and moves with very low power. Wondering if could be a sensor problem or since the car sat maybe bad fuel.

Patrick

33 years of experience
369 reviews
Patrick
33 years of experience
Geo Tracker L4-1.6L - Oil/Fluid Leak - Las Vegas, Nevada
Amazing Guy! he took his time explaining everything he knew about the crank and canm shift. Thank you again Patrick I hope to see you soon once I get my cash situation figured out.

Excellent Rating

(15)

Rating Summary
14
1
0
0
0
14
1
0
0
0
Number of Geo Tracker services completed
165+
services done by our mechanics
TOTAL NUMBER OF EXPERT Geo MECHANICS
70+
experts on our platform

Recent articles & questions

Is It Safe to Drive While Taking Antihypertensives?
Do Do you have high blood pressure? If so, you may have had antihypertensive medication prescribed to you by your doctor. As is the case with many medications, there can be side effects, some of which may affect your ability...
A Buyer’s Guide to the 2012 Hyundai Sonata Hybrid
When When Toyota first introduced the Prius, the idea seemed to be that all hybrids and electric cars had to have their own specific models and that they couldn’t look like normal cars. A lot of consumers weren’t too thrilled...
How Long Does a Throttle/Accelerator Pedal Position Sensor Last?
The The throttle/accelerator pedal position sensor detects the position of the accelerator pedal. This information is then transmitted to the vehicle’s computer - the engine control module (ECM). From there, the data is then sent from the computer to the...

Getting multiple codes

Hello. When you get these codes together it is typically the result of a vacuum leak. If there is too much air entering the engine, your truck will have idling problems and this will cause issues with the oxygen sensor...

1984 ranger revving high before shifting into gear. Automatic Transmission

This may be a sign of a faulty MAP sensor as the vehicle responds adversely to a load put on the motor (i.e. putting it in gear, making turns (which makes use of the power steering pressure switch) turning on...

Car jerking when stopped or when trying to change gears

I would classify this as rough operation/loss of power (https://www.yourmechanic.com/services/car-idle-is-rough-inspection). To find the exact cause will require an on-site inspection and that inspection can be performed on a mobile basis right at your location. Rough operation could be due to...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com