Fiat 124 Spider Car starts and then dies Inspection at your home or office.

Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.

Estimate price near me

Service Location

Customer Ratings

(4)

How A Diagnostic Works

Instantly book a certified mobile mechanic to come to you

Mechanic diagnoses the problem and quotes necessary repairs

Your vehicle is ready to go

Fair, upfront & transparent pricing for all services

Our certified mobile mechanics can come to you now.

Customer Ratings

(4)

Car starts and then dies Inspection Service

How much does a Car starts and then dies Inspection cost?

On average, the cost for a Fiat 124 Spider Car starts and then dies Inspection is $95 with $0 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2019 Fiat 124 SpiderL4-1.4L TurboService typeCar starts and then dies InspectionEstimate$114.99Shop/Dealer Price$124.99 - $132.49
2018 Fiat 124 SpiderL4-1.4L TurboService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$105.01 - $112.52
2020 Fiat 124 SpiderL4-1.4L TurboService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$105.01 - $112.52
2017 Fiat 124 SpiderL4-1.4L TurboService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$104.99 - $112.48
Show example Fiat 124 Spider Car starts and then dies Inspection prices

Starting a vehicle only to have it quit immediately after can be confusing and annoying for many drivers especially if their vehicle has not experienced this type of issue before. Typically, a vehicle will start and then quit because of an issue with the fuel or electrical system. It is important to monitor fuel levels as well as warning lights which can signal to the driver that a vehicle may quit unexpectedly.

How this system works:

To start a vehicle, the electrical system, composed of the battery and starter, turns the engine over. Once running, the engine requires a constant flow of gasoline and good spark to keep that fuel igniting. If gasoline is not readily available, or if there is not enough spark, the engine will quit. More modern vehicles with sophisticated computers may affect the way the vehicle runs. These computers help the car run efficiently but can also shut a car down if the fuel/air mixture is not correct. While an older vehicle may be less sophisticated and easier to diagnose, the computers on modern cars can provide more specific information when connected to a code scanner/reader.

Common reasons for this to happen:

  • Mass Airflow Sensor: The mass airflow sensor measures how much air is entering the engine and relays this information to the vehicle’s computer so that the right amount of fuel can be delivered from the fuel injectors. When a sensor begins to fail, the vehicle’s computer may generate an error code to indicate that something has gone wrong. An issue with the mass airflow sensor may manifest itself when a car starts and then stalls soon after starting.

  • Fuel Pump Relay: The fuel pump relay functions much like a fuse for an electric fuel pump. The fuel pump relay engages as the vehicle is started and starts the fuel pump. While the vehicle is running, the fuel pump relay turns off and the fuel pump is powered by the oil pressure sending unit. If the vehicle’s computer is unable to keep the fuel pump relay running throughout the starting process, the vehicle may start and quit immediately after starting.

  • Ignition Coil: Your vehicle’s ignition coil takes the low voltage of the battery and provides the thousands of volts needed to create a spark in the spark plugs. When an ignition coil begins to fail, it may struggle to provide consistent spark to the plugs, causing the engine to stall after starting.

What to expect:

A top-rated mobile mechanic will come to your home or office to determine the reason why the vehicle starts and then dies. The mechanic will then provide a detailed inspection report outlining why the vehicle quit and the cost of any repairs that need to be made.

How it's done:

A mechanic will begin diagnosing your vehicle’s issue by plugging a code reader/scanner into the vehicle’s computer. The mechanic should be able to get more information from your vehicle’s computer on what component has failed. Using this information, the mechanic can begin necessary repairs.

If your vehicle has a bad or failing mass airflow sensor, the mechanic will begin by finding the sensor in the engine bay and checking for any signs of failure. The mechanic should check the wire harness connected to the sensor to ensure that all of wires are properly connected. After removing the sensor, the mechanic should be able to discover the nature of the failure and replace the sensor.

If the mechanic suspects an issue with the fuel pump relay, he or she should check the vehicle’s computer for a problem. If the vehicle’s computer is having difficulty providing consistent power to the fuel pump relay, the computer may need to be reprogrammed or replaced. If the vehicle’s computer is functioning normally, the mechanic may need to replace the fuel pump relay.

If the mechanic suspects that the ignition coil may be faulty, he or she should first disconnect the battery before beginning work. The mechanic should then begin the process of disconnecting wires from the ignition coil and removing it from the engine bay. The mechanic will then install the new ignition coil and ensure that it is connected properly. The mechanic should then reconnect the battery and test the new coil.

With all repairs, the mechanic will ensure the newly installed parts work properly. The mechanic can then turn off and warning lights that may have come on while the vehicle was not running properly.

How important is this service?

If your vehicle is starting but dying soon after starting, you should have it checked out by a mechanic. Issues involving the fuel management and electrical systems will become worse if not dealt with. Diligence and paying attention to warning lights may help prevent further damage to critical engine component and may save money in repairs. A vehicle that quits after starting can be inconvenient and having a mobile mechanic inspect and repair you vehicle will ensure that you and your vehicle are back on the road soon.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Fiat mechanics

Real customer reviews from Fiat owners like you.

Excellent Rating

(4)

Rating Summary
3
0
0
0
1
3
0
0
0
1

Joseph

20 years of experience
649 reviews
Joseph
20 years of experience
Fiat 124 Spider L4-1.4L Turbo - Check Engine Light is on - Sandy, Utah
Couldn't be happier! Very punctual, did a good job and cleanly.

Henry

34 years of experience
172 reviews
Henry
34 years of experience
Fiat 124 Spider L4-1.4L Turbo - Car is not starting - Glassboro, New Jersey
Was a wonderful person did his job well enjoyed talking with him

Damian

11 years of experience
465 reviews
Damian
11 years of experience
Fiat 124 Spider L4-1.4L Turbo - Oil Change - Crofton, Maryland
Great experience with Damian... Very personable !

Dellano

18 years of experience
518 reviews
Dellano
18 years of experience
Fiat 500 L4-1.4L - Air Filter - Silver Spring, Maryland
Dellano was prompt, respectful, removed what I didn't need from the invoice, and let me know what I needed for future maintenance. All while competing everything in well less than the time that was quoted. Highly recommend.

Excellent Rating

(4)

Rating Summary
3
0
0
0
1
3
0
0
0
1
Number of Fiat 124 Spider services completed
44+
services done by our mechanics
TOTAL NUMBER OF EXPERT Fiat MECHANICS
300+
experts on our platform

Recent articles & questions

How Long Does a Blower Motor Switch Last?
Keeping Keeping the cabin of a car at the right temperature is no easy job. A number of components have to work together in order for your car’s cabin to stay comfortable. The heating and A/C systems in your car...
P0764 OBD-II Trouble Code: Shift Solenoid C Intermittent
P0764 means a faulty shift solenoid and irregular voltage readings; caused by a failed shift solenoid, internal ATF blockages
P0637 OBD-II Trouble Code: Power Steering Control Circuit High
P0637 means there is an issue with the powers steering control circuit due to faulty electrical components, damaged ground wire or a loose strap.

Hesitation, stalling out

Hello. It sounds like the spark plugs are fouled and the spark plug wires need to be replaced. It is possible that the fuel filter (https://www.yourmechanic.com/services/fuel-filter-replacement) is clogged up and needs to be replaced as well. Have a certified technician,...

Squeaking sound coming from the front of the car when driving slow

This is very likely related to something that increases with engine speed. The drive or serpentine belts can make squeaking noises that will speed up as they do with engine speed. This is usually due to a loose or slipping...

Leaking anti freeze

You most likely have a leaking water pump or radiator. I would recommend first looking to see if you notice where the leak is before starting the vehicle. If the leak cannot be identified then I recommend adding coolant dye...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com