Buick LeSabre Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(356)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(356)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Buick LeSabre Tie Rod End Replacement is $146 with $51 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1969 Buick LeSabreV8-5.7LService typeTie Rod End - Front Left Outer ReplacementEstimate$345.31Shop/Dealer Price$412.89 - $593.13
1974 Buick LeSabreV8-7.5LService typeTie Rod End - Rear Right Outer ReplacementEstimate$292.67Shop/Dealer Price$352.11 - $507.88
1974 Buick LeSabreV8-7.5LService typeTie Rod End - Front Left Inner ReplacementEstimate$382.91Shop/Dealer Price$464.91 - $688.36
1998 Buick LeSabreV6-3.8LService typeTie Rod End - Rear Right Inner ReplacementEstimate$468.93Shop/Dealer Price$542.15 - $689.86
1968 Buick LeSabreV8-5.7LService typeTie Rod End - Rear Right Outer ReplacementEstimate$325.31Shop/Dealer Price$392.92 - $573.19
1966 Buick LeSabreV8-5.6LService typeTie Rod End - Rear Right Inner ReplacementEstimate$359.87Shop/Dealer Price$436.11 - $642.28
1968 Buick LeSabreV8-5.7LService typeTie Rod End - Rear Right Inner ReplacementEstimate$407.11Shop/Dealer Price$493.77 - $731.52
1986 Buick LeSabreV8-5.0LService typeTie Rod End - Front Right Inner ReplacementEstimate$374.07Shop/Dealer Price$427.78 - $526.63
Show example Buick LeSabre Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Buick mechanics

Real customer reviews from Buick owners like you.

Excellent Rating

(356)

Rating Summary
326
22
3
2
3
326
22
3
2
3

Joseph

15 years of experience
12 reviews
Joseph
15 years of experience
LeSabre 1998 - Car is not starting - Ravenel, SC
Joe is great! Very friendly, professional and knowledgeable.

Joseph

15 years of experience
12 reviews
Joseph
15 years of experience
LeSabre 1998 - Radiator - Ravenel, SC
Joe was incredible! Very nice and professional. I will definitely request him again very soon for other repairs needed. He got my car running and that was the priority this time.

Joshua

6 years of experience
35 reviews
Joshua
6 years of experience
LeSabre 2002 - Power steering fluid is leaking - Denton, TX
Josh is not only professional he is very nice and friendly. This was the first time using the service and he was able to answer my questions with no problem.

Alexander

5 years of experience
126 reviews
Alexander
5 years of experience
LeSabre 2003 - Power Steering Pressure Hose - Columbus, OH
Awesome work despite all the rust he had to deal with. Very friendly, helpful and transparent.

Excellent Rating

(356)

Rating Summary
326
22
3
2
3
326
22
3
2
3
Number of Buick LeSabre services completed
3916+
services done by our mechanics
TOTAL NUMBER OF EXPERT Buick MECHANICS
800+
experts on our platform

Recent articles & questions

P0125 OBD-II Trouble Code: Insufficient Coolant Temperature for Closed Loop Fuel Control
P0125 code definition Insufficient Coolant Temperature For Closed Loop Fuel Control What the P0125 code means P0125 is the OBD-II generic code...
How to Get Smog Technician Certified in North Carolina
Automotive technician jobs include smog certified emissions inspectors. In North Carolina, you need to work at a licensed inspection station.
Understanding Ford Intelligent Oil-Life Monitor (IOLM) System and Lights
Car symbols, or dashboard lights, are a car service reminder. The Ford Intelligent Oil-Life Monitor indicates when and what service your car needs.

How do I change the display?

You can change the display based on what you would like the audio system to show you. The display has two available options: Title (the song name or program title will be displayed), and Name/Title (artist and song name, or...

What all transmissions are interchangeable with my vehicle

Hello. It really depends on which rear end that you have and if the vehicle is four-wheel drive. If it is four-wheel drive then the differential gearing has to be the same in the front and the rear so you...

2007 hyundai tucson . oil light came on first then car started to slow down . it caught back up the started to slow down again. I pulled over and now the car won't start. I used starter fluid, nothing. I pulled a spark plug but am getting no spark

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com