BMW 435i xDrive Brake Drum Replacement Costs

Car	Service	Estimate	Shop/Dealer Price
2016 BMW 435i xDriveL6-3.0L Turbo	Service typeBrake Drum Replacement	Estimate$663.51	Shop/Dealer Price$812.51 - $1200.47
2015 BMW 435i xDriveL6-3.0L Turbo	Service typeBrake Drum Replacement	Estimate$633.51	Shop/Dealer Price$782.56 - $1170.55
2014 BMW 435i xDriveL6-3.0L Turbo	Service typeBrake Drum Replacement	Estimate$633.51	Shop/Dealer Price$782.56 - $1170.54

Car

Service

Estimate

Shop/Dealer Price

2016 BMW 435i xDriveL6-3.0L Turbo

Service typeBrake Drum Replacement

Estimate$663.51

Shop/Dealer Price$812.51 - $1200.47

2015 BMW 435i xDriveL6-3.0L Turbo

Service typeBrake Drum Replacement

Estimate$633.51

Shop/Dealer Price$782.56 - $1170.55

2014 BMW 435i xDriveL6-3.0L Turbo

Service typeBrake Drum Replacement

Estimate$633.51

Shop/Dealer Price$782.56 - $1170.54

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(6)

Rating Summary

SEE REVIEWS NEAR ME

Duane

25 years of experience

519 reviews

Request Duane

by Daniel

BMW 435i xDrive L6-3.0L Turbo - Oil Change - Oceanside, California

Great experience, really professional. Easy, convenient and all that in the comfort of my garage with a nice coffee!!

Alfred

13 years of experience

512 reviews

Request Alfred

by Thu

BMW 435i xDrive L6-3.0L Turbo - Oil Change - San Francisco, California

Super straightforward, efficient and clean. Would recommend 10/10

Scott

36 years of experience

909 reviews

Request Scott

by Tyler

BMW 435i xDrive L6-3.0L Turbo - Brake Rotor/Disc Replacement (Front) - Scottsdale, Arizona

Scott was right on time and finished the job in a timely manner. Great guy, will most definitely recommend him to friends & family!

Erfan

7 years of experience

21 reviews

Request Erfan

by Deon

BMW 435i xDrive L6-3.0L Turbo - Brake Pads Replacement (Front, Rear) - Kirkland, Washington

Efran, Arrived an hour and half early and was able to finish putting on new brake pads, rotors and sensors on my 2014 BMW 435i Xdrive in approximately 3 hours. Efran, was extremely professional, knowledgeable and easy to speak with. Not only would I use Efran again, I highly recommend him.

BMW 435i xDrive Brake Drum Replacement at your home or office.

Estimate price near me

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a BMW 435i xDrive Brake Drum Replacement is $388 with $246 for parts and $142 for labor. Prices may vary depending on your location.

What are brake drums and how do they work?

When to consider replacing brake drums:

How do mechanics replace brake drums?

Is it safe to drive with a brake drum problem?

When replacing brake drums keep in mind:

Meet some of our expert BMW mechanics

Excellent Rating

Rating Summary

Duane

Alfred

Scott

Erfan

Excellent Rating

Rating Summary

Recent articles & questions

Driver's side window not working.

How to get my truck home with no brakes but a engine.

WHERE IS THE VAPOR CANISTER VENT VALVE ON 2012 CHEVROLET CAPTIVA V6? IS IT ON THE CANISTER? ALSO WHERE IS THE FUEL PRESSURE SENSOR

How can we help?