Toyota Pickup Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(181)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(181)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Toyota Pickup Brake Drum Replacement is $395 with $187 for parts and $209 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1972 Toyota PickupL4-2.0LService typeBrake Drum ReplacementEstimate$850.76Shop/Dealer Price$1018.45 - $1467.54
1984 Toyota PickupL4-2.4L DieselService typeBrake Drum ReplacementEstimate$968.81Shop/Dealer Price$1136.87 - $1519.35
1993 Toyota PickupL4-2.4LService typeBrake Drum ReplacementEstimate$585.36Shop/Dealer Price$701.49 - $1000.31
1989 Toyota PickupL4-2.4LService typeBrake Drum ReplacementEstimate$584.82Shop/Dealer Price$700.77 - $999.14
1979 Toyota PickupL4-2.2LService typeBrake Drum ReplacementEstimate$761.52Shop/Dealer Price$918.98 - $1337.20
1985 Toyota PickupL4-2.4L TurboService typeBrake Drum ReplacementEstimate$620.78Shop/Dealer Price$743.02 - $1055.65
1995 Toyota PickupL4-2.4LService typeBrake Drum ReplacementEstimate$651.06Shop/Dealer Price$777.54 - $1103.64
1992 Toyota PickupL4-2.4LService typeBrake Drum ReplacementEstimate$596.36Shop/Dealer Price$713.01 - $1012.22
Show example Toyota Pickup Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Toyota mechanics

Real customer reviews from Toyota owners like you.

Excellent Rating

(181)

Rating Summary
166
8
3
3
1
166
8
3
3
1

Tony

14 years of experience
121 reviews
Tony
14 years of experience
Toyota Pickup L4-2.4L - Oil Change - El Sobrante, California

Shawn

12 years of experience
287 reviews
Shawn
12 years of experience
Toyota Pickup L4-2.4L - Distributor - Chester Springs, Pennsylvania
Great experience!

Nicholas

15 years of experience
28 reviews
Nicholas
15 years of experience
Toyota Pickup L4-2.4L - Power Steering Pressure Hose - Oceanside, California
Nicholas was great. Very competent, personable and easy to understand.

Muneshwar

17 years of experience
35 reviews
Muneshwar
17 years of experience
Toyota Pickup L4-2.4L - Serpentine/Drive Belt - Federal Way, Washington
Prompt, courteous, showed me how to see that one belt was loose and cracked from age and that the other two were cracked. He came to replace the loose one but was prepared with the others. Explained that they would be OK for awhile or he could do all at once in same hour of labor. After price check and my approval he replaced all three. Now my old '88 truck will keep on keepin' on without another belt going out. He then checked out the whole truck and made recommendations of other minor repairs but left me feeling assured that these could wait for my budget to be ready. Thank you Max.

Excellent Rating

(181)

Rating Summary
166
8
3
3
1
166
8
3
3
1
Number of Toyota Pickup services completed
1991+
services done by our mechanics
TOTAL NUMBER OF EXPERT Toyota MECHANICS
1600+
experts on our platform

Recent articles & questions

Is it Safe to Drive With a Hole In Your Exhaust?
The exhaust collects discarded gases from engine cylinders into one pipe. These gases are then delivered to the exhaust pipe...
How to Transfer a Car Title in Maine
Whether Whether you’re buying or selling a car, or you’re giving one as a gift or about to inherit one, there are some things you’ll need to know. In all of these situations, ownership changes. That means that the title...
How to Shift From First to Second Gear in a Manual Transmission Car
Shifting from first to second gear in a manual transmission requires accuracy and practice, as well as a feel for the car.

How do I open the trunk with the remote keyless entry (RKE) transmitter?

The remote keyless entry (RKE) transmitter can be used to open your vehicle’s trunk. Here’s how: 1. Press the unlock button on the RKE transmitter. The unlock button looks like an open padlock, and will unlock all of the vehicle’s...

Barely any power when I step on the gas pedal, any ideas?

Hello. From the symptoms you describe it would appear that your vehicle is experiencing an issue that is putting it into some sort of limp mode. Limp mode is activated when the computer detects an issue that could potentially damage...

My car has an engine check light orange in colour

You will need to have the Check Engine Light diagnosed by having the computer scanned and any codes diagnosed. Be aware that O2 sensor codes may not be an O2 sensor failure but an engine running lean or too rich....

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com