Oldsmobile Cutlass Calais Power Steering Pressure Hose Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(4)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(4)

Power Steering Pressure Hose Replacement Service

How much does a Power Steering Pressure Hose Replacement cost?

On average, the cost for a Oldsmobile Cutlass Calais Power Steering Pressure Hose Replacement is $219 with $79 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1991 Oldsmobile Cutlass CalaisL4-2.5LService typePower Steering Pressure Hose ReplacementEstimate$328.40Shop/Dealer Price$371.84 - $493.23
1990 Oldsmobile Cutlass CalaisL4-2.3LService typePower Steering Pressure Hose ReplacementEstimate$484.41Shop/Dealer Price$567.38 - $811.76
1990 Oldsmobile Cutlass CalaisV6-3.3LService typePower Steering Pressure Hose ReplacementEstimate$484.41Shop/Dealer Price$567.41 - $811.81
1991 Oldsmobile Cutlass CalaisL4-2.3LService typePower Steering Pressure Hose ReplacementEstimate$325.09Shop/Dealer Price$368.26 - $493.16
1990 Oldsmobile Cutlass CalaisL4-2.5LService typePower Steering Pressure Hose ReplacementEstimate$560.53Shop/Dealer Price$664.18 - $966.88
1991 Oldsmobile Cutlass CalaisV6-3.3LService typePower Steering Pressure Hose ReplacementEstimate$484.41Shop/Dealer Price$567.56 - $812.08
Show example Oldsmobile Cutlass Calais Power Steering Pressure Hose Replacement prices

What is the power steering pressure hose and how does it work?

The power steering pressure hose transfers the high-pressure hydraulic output of the power steering pump to either a steering gear box or steering rack and pinion unit to create the power assist that you rely on when you turn the steering wheel. The pressure hose is only used in cars with a power steering pump and reservoir, so if you have a newer car you may have electric power steering instead. The pressure hose is relatively large in diameter in order to withstand high hydraulic pressure, flex as the engine moves and vibrates, and also withstand engine heat, accidental cuts, and abrasion.

When to the consider replacing the power steering pressure hose:

  • Groaning, whirring noise or difficulty steering. Noise, or difficulty turning the steering wheel, may reflect a low power steering fluid level, which could be due to a leak in a pressure hose, or a leak elsewhere in the power steering system. Although a leak in the pressure hose is a possible cause of a low fluid level, a mechanic will consider all other possible causes, too.
  • Visible fluid leaks. There are usually steel ferrules clamped onto each end of the rubber pressure hose. These ferrules are common leak points. If there is seepage from these ferrules, the pressure hose should be replaced.
  • Hose damage. If the hose has significant physical damage, such as cuts, abrasions, cracks, or heat damage, the hose should be replaced to avoid sudden hose failure.
  • Contaminated fluid. If rubber particles are found in the power steering fluid or reservoir, it means the interior of either the pressure hose or the return hose is deteriorating. All rubber hoses should be replaced and the system flushed. An in-line, aftermarket fluid filter might be required.
  • Hose age. Both the pressure and return hoses are rubber-based products with a limited service life. If the vehicle is more than 10 years old, and power steering components are being replaced, all the rubber hoses should be replaced during that service.

How do mechanics replace the power steering pressure hose?

The underhood routing of the power steering pressure hose varies greatly between car models. The repair procedure ranges from simple to quite involved. The basic steps are:

  • Raise car as needed and support with steel safety stands.
  • Unthread the pressure hose tube nuts, or banjo-style bolts, at each end of the pressure hose.
  • Remove pressure hose and inspect interior hose lining for separation, if visible.
  • Install a new hose, using a new sealing washer or O-ring seals as applicable, and paying particular attention to the required original equipment manufacturer’s (OEM) torque value for the tube nuts or banjo bolts. Replace rubber return hose, if required, and with the authorization of the customer.
  • Once the system is fully sealed again, bleed or flush power steering system as required to remove all air and contaminants.
  • Finally, the engine is run, the car is test driven, and leaks are checked for at all connections.

Is it safe to drive with a power steering pressure hose problem?

No. The fluid in the power steering pressure hose is under very high pressure and flammable. A leak that sprays fluid into a hot engine part, such as the exhaust manifold, can cause a fire. Leaks that cause significant fluid loss can cause difficulty in steering and, if a leak causes the fluid level in the reservoir to drop too low, it can cause damage to the power steering pump too, necessitating the installation of not only a new hose but a new pump.

When replacing the power steering pressure hose keep in mind:

  • When the power steering hoses are replaced, the entire power steering system should be inspected.
  • Use only OEM specified power steering fluid in your power steering system.
  • If the pressure hose has deteriorated from the inside, the rubber return hose should be replaced as well and the system should be flushed. A mechanic might recommend the installation of an in-line filter to capture all debris.
  • Tube nuts and banjo bolts used to seal pressure hoses have OEM-specified torque values. Mechanics will use a calibrated torque wrench to tighten the connections.
  • Complete removal of air from the system can occasionally take some time, even after the normal bleeding procedure. During this time some mild noise may be heard when turning the steering wheel. If it persists more than a day or so, the system should be rechecked.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Oldsmobile mechanics

Real customer reviews from Oldsmobile owners like you.

Excellent Rating

(4)

Rating Summary
4
0
0
0
0
4
0
0
0
0

Ronnaldo

12 years of experience
69 reviews
Ronnaldo
12 years of experience
Oldsmobile Cutlass Calais L4-2.3L - Serpentine/Drive Belt - McDonough, Georgia
He was great, professional and knowledgeable.

Ned

25 years of experience
52 reviews
Ned
25 years of experience
Oldsmobile Cutlass Calais V6-3.8L - Car is not starting - Scottsdale, Arizona
Ned is most thorough and professional;highly knowledgeable. He's a first rate automotive technician.

Robert

43 years of experience
232 reviews
Robert
43 years of experience
Oldsmobile Cutlass Calais V8-5.0L - Brake Pads Replacement (Front) - Spring, Texas
Got right down to business,did good job and went above and beyond.

Fred

18 years of experience
389 reviews
Fred
18 years of experience
Oldsmobile Cutlass Calais V8-5.0L - Adjust Ignition Timing - Spring, Texas
Came to do my timing, diagnosed bad harmonic balancer I totally agree with his assessment. Will be having new one installed.

Excellent Rating

(4)

Rating Summary
4
0
0
0
0
4
0
0
0
0
Number of Oldsmobile Cutlass Calais services completed
44+
services done by our mechanics
TOTAL NUMBER OF EXPERT Oldsmobile MECHANICS
300+
experts on our platform

Recent articles & questions

P3416 OBD-II Trouble Code: Cylinder 2 Exhaust Valve Control Circuit High
P3416 means an issue in engine cylinder number 2 which may cause vehicle to not be able to switch over to lower power mode such as v4.
P0970 OBD-II Trouble Code: Pressure Control Solenoid “C” Control Circuit Low
P0970 means there is a discrepancy between the desired hydraulic pressure and the actual hydraulic pressure due to faulty solenoids.
How the Alternator Works in Your Car
Your Your car alternator, at its most basic, is what works along with your battery and the rest of your charging system to keep your car running. When you start your car, you’re running on battery power. Then the battery...

I can't shift into any gear

It sounds like you may have a throwout bearing that is hanging up. When the car is not running, nothing within the transmission is spinning, thus it is possible to put the car in gear. With the engine running, there...

Your mechanic come and replace oil for my BMW X5, but the car said the oil is below minimal, how to do that?

Hi Tony. Thanks for contacting us today. Sometimes directly after the oil is changed, the oil warning light will illuminate. If it does not clear up within the next day or so, then I would recommend adding one quart of...

What does a red lighting volt mean on a 2011 Jeep Grand Cherokee

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com