Nissan Pulsar NX Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Nissan Pulsar NX Brake Drum Replacement is $534 with $192 for parts and $342 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1989 Nissan Pulsar NXL4-1.6L	Service typeBrake Drum Replacement	Estimate$912.39	Shop/Dealer Price$1054.26 - $1376.35
1988 Nissan Pulsar NXL4-1.6L	Service typeBrake Drum Replacement	Estimate$820.39	Shop/Dealer Price$962.34 - $1284.49
1984 Nissan Pulsar NXL4-1.5L Turbo	Service typeBrake Drum Replacement	Estimate$1005.43	Shop/Dealer Price$1193.63 - $1654.56
1983 Nissan Pulsar NXL4-1.5L Turbo	Service typeBrake Drum Replacement	Estimate$976.94	Shop/Dealer Price$1162.04 - $1620.63
1989 Nissan Pulsar NXL4-1.8L	Service typeBrake Drum Replacement	Estimate$820.39	Shop/Dealer Price$962.41 - $1284.60
1987 Nissan Pulsar NXL4-1.6L	Service typeBrake Drum Replacement	Estimate$820.39	Shop/Dealer Price$962.33 - $1284.48
1986 Nissan Pulsar NXL4-1.6L	Service typeBrake Drum Replacement	Estimate$896.35	Shop/Dealer Price$1050.91 - $1412.30
1983 Nissan Pulsar NXL4-1.6L	Service typeBrake Drum Replacement	Estimate$873.18	Shop/Dealer Price$1038.40 - $1451.01

Show example Nissan Pulsar NX Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Nissan mechanics

Real customer reviews from Nissan owners like you.

Excellent Rating

(8)

Rating Summary

7

0

0

0

1

7

0

0

0

1

SEE REVIEWS NEAR ME

Sean

17 years of experience

111 reviews

Sean

17 years of experience

by Joan

Nissan Pulsar NX L4-1.6L - Car is not starting - Waldorf, Maryland

I had a recurring problem with my older car that was not starting after sitting for a few days. Sean is very knowledgeable and explained the issues very clearly He analyzed the "new" battery and found a dead cell. He gave me a quote of other maintenance things I would need in the future.

Patrick

15 years of experience

406 reviews

Request Patrick

Patrick

15 years of experience

Request Patrick

by Lateisha

Nissan Sentra L4-1.8L - Brake Drum - Highland Springs, Virginia

Great service and very professional. Job was done quick and precise !!

Charles

17 years of experience

176 reviews

Request Charles

Charles

17 years of experience

Request Charles

by Andrew

Nissan Sentra L4-1.8L - Brake Drum - San Carlos, California

Prompt, efficient and did a great job. Thanks Charles!

Javier

9 years of experience

10 reviews

Javier

9 years of experience

by Steven

Nissan Murano V6-3.5L - Brake Drum - Moreno Valley, California

Timely, fast and negotiable

Excellent Rating

(8)

Rating Summary

7

0

0

0

1

7

0

0

0

1

SEE REVIEWS NEAR ME

Recent articles & questions

How Can I Have the Vents Set to Cold Without the AC on?

The The modern automotive HVAC system offers a number of different capabilities to help keep drivers and passengers comfortable during hot or cold weather. There’s the air conditioning system, the heater, and the vent system (which doesn’t use either the...

How Long Does an Air Pump Last?

In In decades gone by, exhaust systems were not all that complicated. Emissions controls were not a concern, and any gases that were spent during the operation of your car were simply vented through the manifold, into the exhaust pipe,...

P0614 OBD-II Trouble Code: ECM / TCM Incompatible

P0614 code means there has been an error in compatibility between the car’s engine control module and TCM often due too corrosion, or bad PCM.

Car starts, but then immediately stalls.

Hi there. When a vehicle sits for a long period of time any number of things can cause this to occur. From the symptoms you are explaining, I would suspect a fuel issue. When a vehicle sits for this long...

Car stalled at 70 mph, SOS warning on

Hello. The purpose of the SOS button is to enable you to call BMW when there is a problem with the car or in the event of an emergency. It sounds like there is a problem with the transmission and...

Traction control not working

Hi There, It sounds like you may have a faulty traction control module. As you know, the traction control system monitors the steering stability of the vehicle and engages when loss of traction has been detected. This is done by...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com