Mercury Topaz Power Steering Pressure Hose Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(6)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(6)

Power Steering Pressure Hose Replacement Service

How much does a Power Steering Pressure Hose Replacement cost?

On average, the cost for a Mercury Topaz Power Steering Pressure Hose Replacement is $224 with $100 for parts and $123 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1986 Mercury TopazL4-2.0L DieselService typePower Steering Pressure Hose ReplacementEstimate$395.66Shop/Dealer Price$462.71 - $625.60
1985 Mercury TopazL4-2.0L DieselService typePower Steering Pressure Hose ReplacementEstimate$361.66Shop/Dealer Price$428.74 - $591.65
1986 Mercury TopazL4-2.3LService typePower Steering Pressure Hose ReplacementEstimate$519.46Shop/Dealer Price$625.99 - $907.25
1994 Mercury TopazV6-3.0LService typePower Steering Pressure Hose ReplacementEstimate$684.61Shop/Dealer Price$837.88 - $1268.47
1988 Mercury TopazL4-2.3LService typePower Steering Pressure Hose ReplacementEstimate$528.96Shop/Dealer Price$636.52 - $918.55
1990 Mercury TopazL4-2.3LService typePower Steering Pressure Hose ReplacementEstimate$528.96Shop/Dealer Price$636.49 - $918.50
1989 Mercury TopazL4-2.3LService typePower Steering Pressure Hose ReplacementEstimate$537.96Shop/Dealer Price$645.24 - $927.07
1993 Mercury TopazV6-3.0LService typePower Steering Pressure Hose ReplacementEstimate$691.11Shop/Dealer Price$844.72 - $1275.56
Show example Mercury Topaz Power Steering Pressure Hose Replacement prices

What is the power steering pressure hose and how does it work?

The power steering pressure hose transfers the high-pressure hydraulic output of the power steering pump to either a steering gear box or steering rack and pinion unit to create the power assist that you rely on when you turn the steering wheel. The pressure hose is only used in cars with a power steering pump and reservoir, so if you have a newer car you may have electric power steering instead. The pressure hose is relatively large in diameter in order to withstand high hydraulic pressure, flex as the engine moves and vibrates, and also withstand engine heat, accidental cuts, and abrasion.

When to the consider replacing the power steering pressure hose:

  • Groaning, whirring noise or difficulty steering. Noise, or difficulty turning the steering wheel, may reflect a low power steering fluid level, which could be due to a leak in a pressure hose, or a leak elsewhere in the power steering system. Although a leak in the pressure hose is a possible cause of a low fluid level, a mechanic will consider all other possible causes, too.
  • Visible fluid leaks. There are usually steel ferrules clamped onto each end of the rubber pressure hose. These ferrules are common leak points. If there is seepage from these ferrules, the pressure hose should be replaced.
  • Hose damage. If the hose has significant physical damage, such as cuts, abrasions, cracks, or heat damage, the hose should be replaced to avoid sudden hose failure.
  • Contaminated fluid. If rubber particles are found in the power steering fluid or reservoir, it means the interior of either the pressure hose or the return hose is deteriorating. All rubber hoses should be replaced and the system flushed. An in-line, aftermarket fluid filter might be required.
  • Hose age. Both the pressure and return hoses are rubber-based products with a limited service life. If the vehicle is more than 10 years old, and power steering components are being replaced, all the rubber hoses should be replaced during that service.

How do mechanics replace the power steering pressure hose?

The underhood routing of the power steering pressure hose varies greatly between car models. The repair procedure ranges from simple to quite involved. The basic steps are:

  • Raise car as needed and support with steel safety stands.
  • Unthread the pressure hose tube nuts, or banjo-style bolts, at each end of the pressure hose.
  • Remove pressure hose and inspect interior hose lining for separation, if visible.
  • Install a new hose, using a new sealing washer or O-ring seals as applicable, and paying particular attention to the required original equipment manufacturer’s (OEM) torque value for the tube nuts or banjo bolts. Replace rubber return hose, if required, and with the authorization of the customer.
  • Once the system is fully sealed again, bleed or flush power steering system as required to remove all air and contaminants.
  • Finally, the engine is run, the car is test driven, and leaks are checked for at all connections.

Is it safe to drive with a power steering pressure hose problem?

No. The fluid in the power steering pressure hose is under very high pressure and flammable. A leak that sprays fluid into a hot engine part, such as the exhaust manifold, can cause a fire. Leaks that cause significant fluid loss can cause difficulty in steering and, if a leak causes the fluid level in the reservoir to drop too low, it can cause damage to the power steering pump too, necessitating the installation of not only a new hose but a new pump.

When replacing the power steering pressure hose keep in mind:

  • When the power steering hoses are replaced, the entire power steering system should be inspected.
  • Use only OEM specified power steering fluid in your power steering system.
  • If the pressure hose has deteriorated from the inside, the rubber return hose should be replaced as well and the system should be flushed. A mechanic might recommend the installation of an in-line filter to capture all debris.
  • Tube nuts and banjo bolts used to seal pressure hoses have OEM-specified torque values. Mechanics will use a calibrated torque wrench to tighten the connections.
  • Complete removal of air from the system can occasionally take some time, even after the normal bleeding procedure. During this time some mild noise may be heard when turning the steering wheel. If it persists more than a day or so, the system should be rechecked.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercury mechanics

Real customer reviews from Mercury owners like you.

Excellent Rating

(6)

Rating Summary
6
0
0
0
0
6
0
0
0
0

Jose

10 years of experience
285 reviews
Jose
10 years of experience
Mercury Topaz L4-2.3L - Car is not starting - Zephyrhills, Florida
Very professional, on time and polite.

Andrian

32 years of experience
185 reviews
Andrian
32 years of experience
Mercury Topaz L4-2.3L - Battery Cable Replacement (Negative) - Pompano Beach, Florida
A nicer person you could NOT find. Friendly, knowledgeable and timely. Goes the extra mile to make sure the job is done correctly and point out other issues to consider. Would NOT hesitate to book with him for future repairs or recommend to others. If you require auto service - BOOK HIM!!!

Matt

11 years of experience
2 reviews
Matt
11 years of experience
Mercury Mountaineer V6-4.0L - Power Steering Pressure Hose - Pittsburgh, Pennsylvania
Matt was very good and appeared to know cars and how to repair them very well.

Leondo

21 years of experience
9 reviews
Leondo
21 years of experience
Mercury Milan L4-2.3L - Power Steering Pressure Hose - Pittsburgh, Pennsylvania
Thos service is amazing, thank you so much, I will definitely refer to everyone.

Excellent Rating

(6)

Rating Summary
6
0
0
0
0
6
0
0
0
0
Number of Mercury Power Steering Pressure Hose Replacement services completed
66+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercury MECHANICS
600+
experts on our platform

Recent articles & questions

Symptoms of a Bad or Failing Universal Joint (U-Joint)
Common signs of a faulty u-joint include a squeaking noise, clunking sound when shifting, vibrations in the car, and transmission fluid leaking.
P2285 OBD-II Trouble Code: Injector Control Press Sensor Circuit Low
P2285 P2285 code definition Injector Control Press Sensor Circuit Low What the P2285 code means P2285 is an OBD-II generic code for the engine control module (ECM) detecting the injector control pressure (ICP) sensor is low and below specified sensor...
P0383 OBD-II Trouble Code: Glow Plug Control Module Control Circuit Low
Trouble code P0383 means the PCM has detected a low voltage reading of the glow plug heater circuit.

Will turn over but won't start - 1968 Chevrolet C10 Pickup

Hello. You need to see if you have power to one side of the coil and blinking power on the other side when you crank the engine. If you do and no spark comes out of the coil, then replace...

Vehicle does not move when put into gear

A vehicle that won't move in any gear indicates either the transmission is low on fluid, or there is an internal problem. The electronic transmission controls can essentially be ruled out. The 4F50N transmission found in your vehicle has some...

When shifting from reverse to drive or drive to reverse I hear a clicking noise.

Hi there. There is a gear train issue with your transmission or a bad CV Shaft (https://www.yourmechanic.com/services/axle-cv-shaft-assembly-replacement) that is causing the transmission to shift had into gear. Since it shifts harder in reverse than forward, I suggest that the gears...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com