Mercury Park Lane Control Arm Assembly Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(12)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(12)

Control Arm Assembly Replacement Service

How much does a Control Arm Assembly Replacement cost?

On average, the cost for a Mercury Park Lane Control Arm Assembly Replacement is $174 with $79 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1964 Mercury Park LaneV8-6.4LService typeControl Arm Assembly - Rear Upper Left ReplacementEstimate$383.71Shop/Dealer Price$460.89 - $669.93
1964 Mercury Park LaneV8-7.0LService typeControl Arm Assembly - Rear Lower Right ReplacementEstimate$321.47Shop/Dealer Price$388.11 - $565.48
1964 Mercury Park LaneV8-6.4LService typeControl Arm Assembly - Front Lower Left ReplacementEstimate$402.11Shop/Dealer Price$488.91 - $726.76
1965 Mercury Park LaneV8-7.0LService typeControl Arm Assembly - Front Lower Left ReplacementEstimate$402.11Shop/Dealer Price$488.89 - $726.72
1964 Mercury Park LaneV8-7.0LService typeControl Arm Assembly - Front Lower Right ReplacementEstimate$396.35Shop/Dealer Price$481.72 - $715.27
1965 Mercury Park LaneV8-6.4LService typeControl Arm Assembly - Front Upper Right ReplacementEstimate$411.61Shop/Dealer Price$499.41 - $738.01
1967 Mercury Park LaneV8-6.4LService typeControl Arm Assembly - Front Lower Left ReplacementEstimate$407.11Shop/Dealer Price$493.77 - $731.52
1964 Mercury Park LaneV8-7.0LService typeControl Arm Assembly - Front Upper Right ReplacementEstimate$417.11Shop/Dealer Price$505.17 - $743.97
Show example Mercury Park Lane Control Arm Assembly Replacement prices

What is a control arm and how does it work?

A control arm is a suspension component, usually made of heavy gauge steel or aluminum, that links the steering knuckle in the front — or axle carrier in the rear — to the frame of the vehicle. Many vehicles have upper and lower control arms. The inboard link(s) of the arm securely bolt to the frame of the vehicle through rubber bushings, while the outboard link of the control arm connects to the steering knuckle through a ball joint; all of which allow the control of the up and down movement of the steering knuckle or axle carrier. This minimizes the transmission of shock and vibration to the vehicle’s body.

When to consider replacing a control arm:

The structural portion of the control arm can last the life of the vehicle — except for cases of corrosion or crash damage. However, the rubber bushings and the ball joint in a control arm have a limited life. A mechanic should investigate if you notice:

  • Wheel alignment difficulties. Should the bushings, or the ball joint, in a control arm be worn, it will be impossible to properly align the vehicle. The worn components, or the entire arm, must be replaced.
  • Vehicle won’t track straight or pulls to one side. A car will not track straight and may require constant steering correction if there is a worn, bent, or loose control arm.
  • Clunking or squeaking noise. A loose control arm, or a control arm with dried out, rotted, or loose bushings, may move enough to cause detectable noise from the suspension as you go over bumps in the road.
  • Vehicle pulls to one side only when braking. Worn bushings or ball joints can allow control arm to shift when braking, causing the vehicle to pull to one side. Although, this could also be caused by brake calipers.

How do mechanics replace a control arm?

  • The vehicle is raised and supported on steel jack stands, and the wheel and tire assembly is removed.
  • Stabilizer bar links are detached from the control arm, if applicable. ABS wiring to the wheel speed sensor, if routed along the arm, is disconnected.
  • Control arm mounting bolts are detached from the frame and from the axle carrier if the control arm is in the rear.
  • For front control arms connected to the steering knuckle via a ball joint, the nut is removed from the ball joint stud and the stud is pushed through the steering knuckle to free the arm.
  • The arm is lowered from the vehicle and examined by the mechanic to confirm that the noise, or other problem, actually originated from a defect in the arm.
  • The new arm is installed using new mounting bolts if required by the service manual. In many cases, the fasteners must be tightened with the vehicle weight on the suspension in order to ensure the bushings are in a neutral, or resting, position.
  • The vehicle is lowered and road tested to confirm the problem is resolved. Replacing a control arm will change the vehicle alignment settings and the mechanic will refer you to a professional alignment shop to have the vehicle alignment set to factory specifications.

Is it safe to drive with a control arm problem?

No. If the car wanders on the road, pulls to one side, or noise from the suspension is loud, you need to schedule repair right away. Should the problem be limited to low levels of noise, such as clunking or squeaking, continued use of the car is reasonable until you can schedule a repair. Should the control arms be damaged as a result of a collision, it would be unsafe to drive the car until it is repaired.

When replacing a control arm keep in mind:

  • The number of control arm types vary from vehicle to vehicle depending on the design of the vehicle suspension.
  • Control arms should be replaced in pairs — arms on both sides of a front or rear axle — if the reason for replacement is worn control arm bushings or a worn ball joint.
  • All other suspension components should be inspected when control arms are replaced because looseness, damage, or excessive wear in other parts of the suspension system will make it impossible to perform a wheel alignment after the control arms are replaced.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercury mechanics

Real customer reviews from Mercury owners like you.

Excellent Rating

(12)

Rating Summary
11
1
0
0
0
11
1
0
0
0

Robert

20 years of experience
1089 reviews
Robert
20 years of experience
Mercury Park Lane V8-6.4L - Brake Wheel Cylinder Replacement (Driver Side, Passenger Side) - Louisville, Colorado
Excellent work, prompt, courteous.

Jonathan

13 years of experience
171 reviews
Jonathan
13 years of experience
Mercury Milan L4-2.3L - Control Arm Assembly Replacement (Front Lower Left) - Attleboro, Massachusetts
Jonathan was on time, very nice, knowledgeable, and went above and beyond to get my car fixed. He was out in wet crappy weather but kept a smile the whole time.

Mike

26 years of experience
141 reviews
Mike
26 years of experience
Mercury Villager V6-3.3L - Control Arm Assembly Replacement (Front Lower Left, Front Lower Right) - New Boston, Michigan
Very knowledgeable. Does good work.

David

11 years of experience
225 reviews
David
11 years of experience
Mercury Grand Marquis V8-4.6L - Control Arm Assembly Replacement (Front Upper Left, Front Upper Right, Front Lower Left, Front Lower Right) - Kansas City, Missouri
Other than being late, David was great!

Excellent Rating

(12)

Rating Summary
11
1
0
0
0
11
1
0
0
0
Number of Mercury Control Arm Assembly Replacement services completed
132+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercury MECHANICS
600+
experts on our platform

Recent articles & questions

A Buyer's Guide to the 2012 Buick Regal eAssist
Although Although a lot changed about the Buick Regal in 2012, the addition of a hybrid model was definitely the biggest head turner. Whether you want to do your part for the environment or simply save at the pump, this...
P3427 OBD-II Trouble Code: Cylinder 4 Deactivation/Intake Valve Control Circuit Low
What What the P3427 code means When starting, and when the vehicle is operating under heavy weight, the engine will operate in V8 mode. But when driving conditions are light, the engine will deactivate 4 of the 8 cylinders, thereby...
P1102 OBD-II Trouble Code: Mass Airflow Sensor in Range But Lower Than Expected
P1102 means the mass airflow sensor is not working properly, likely due to a bad connection in the sensor, an air leak, or a faulty sensor.

Car jerks while driving and warning lights are on - 2001 Ford Focus

The major causes of sputtering (https://www.yourmechanic.com/services/engine-is-sputtering-inspection) or jerking while driving are caused by fuel, spark, or electrical issues. Due to the number of emergency warning lights that flash, it is likely a power supply issue. This can be caused by...

I have a 1996 benz c280 care needs throttle body actuator have problems getting this in jamaica

Hello, it is unfortunate you are having issues find parts. You may want to try cleaning the throttle itself, cleaning the idle air control valve, and making sure the air filter and housing is clean. Make sure the throttle actuator's...

My truck won’t start

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com