Mercury Monterey Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(20)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(20)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mercury Monterey Brake Drum Replacement is $305 with $172 for parts and $133 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1973 Mercury MontereyV8-5.8LService typeBrake Drum ReplacementEstimate$893.22Shop/Dealer Price$1071.53 - $1552.46
1967 Mercury MontereyV8-6.7LService typeBrake Drum ReplacementEstimate$679.96Shop/Dealer Price$817.00 - $1174.02
1960 Mercury MontereyV8-5.1LService typeBrake Drum ReplacementEstimate$679.96Shop/Dealer Price$816.99 - $1174.01
1972 Mercury MontereyV8-7.5LService typeBrake Drum ReplacementEstimate$679.96Shop/Dealer Price$816.94 - $1173.92
1974 Mercury MontereyV8-7.5LService typeBrake Drum ReplacementEstimate$679.96Shop/Dealer Price$817.03 - $1174.08
1962 Mercury MontereyV8-5.8LService typeBrake Drum ReplacementEstimate$845.22Shop/Dealer Price$1023.57 - $1504.53
1973 Mercury MontereyV8-7.5LService typeBrake Drum ReplacementEstimate$691.96Shop/Dealer Price$828.67 - $1185.44
1968 Mercury MontereyV8-6.4LService typeBrake Drum ReplacementEstimate$703.22Shop/Dealer Price$843.64 - $1209.52
Show example Mercury Monterey Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercury mechanics

Real customer reviews from Mercury owners like you.

Excellent Rating

(20)

Rating Summary
20
0
0
0
0
20
0
0
0
0

Krystal

17 years of experience
106 reviews
Krystal
17 years of experience
Mercury Monterey V6-4.2L - Brake System Flush - Chicago, Illinois
As usual, Krystal was very prompt, professional, and, pleasant.

Irven

11 years of experience
60 reviews
Irven
11 years of experience
Mercury Monterey V6-4.2L - Fuel Pump - Lutherville Timonium, Maryland
Irven arrived on time and worked efficiently. He was thorough in taking the van for a test drive to ensure that everything was working properly. This allowed him to make a needed adjustment. He was friendly and professional.

Krystal

17 years of experience
106 reviews
Krystal
17 years of experience
Mercury Monterey V6-4.2L - Spark Plugs - Chicago, Illinois
Krystal was great! Showed up on time, and completed the work in a very timely manner.

Jeff

13 years of experience
46 reviews
Jeff
13 years of experience
Mercury Monterey V6-4.2L - Car is not starting - Reisterstown, Maryland
He communicated well upon scheduling and when he would arrive for the appointment. He was thorough and explained his diagnosis of the problem. Highly recommend.

Excellent Rating

(20)

Rating Summary
20
0
0
0
0
20
0
0
0
0
Number of Mercury Monterey services completed
220+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercury MECHANICS
600+
experts on our platform

Recent articles & questions

Symptoms of a Bad or Failing Clutch Cable
If your manual car's transmission is slipping out of gear or clutch pedal is hard or sinking to the floor, you may have to replace the clutch cable.
Symptoms of a Bad or Failing Instrument Voltage Regulator
Common signs include dim or flickering gauges, inaccurate or erratic readings from the voltage regulator, and an inoperable instrument cluster.
The Guide to Right-of-Way Laws
One One of the most important facets of being a safe driver is understanding right-of-way laws. Right-of-way laws are the laws that govern who gets priority of the road, and who gets to go first when two drivers (or a...

battery cable is too short to reach battery connection. Had to replace the connection because it broke off and now cable to short

You can purchase battery terminal ends with cables attached at most automotive part stores. You want to find the same gauge/thickness of wire or slightly larger. Then you'll need a lug or crimp fitting that matches the size of the...

Car runs rough, Check Engine Light on, and bad fuel mileage - 2005 Suzuki Verona

Hi there. I would start first by checking for codes that are causing the Check Engine light to come on. This will direct diagnosis and let you know if it related to fuel, spark, compression, or another system. Have a...

The gas pedal needs to be fully pushed in order to touch the Button sensor. It does "click".

There should be stored trouble codes that once downloaded will narrow the focus of the diagnostic. If you suspect that the accelerator pedal sensor (aka, "pedal value sensor") is faulty, that component has to be tested to rule it in...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com