Mercury Cyclone Brake Pad Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

customer ratings

(76)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

customer ratings

(76)

Brake Pad Replacement Estimate for Mercury Cyclone

Mercury Cyclone Brake Pad Replacement costs $174 on average.

CarServiceEstimateShop/Dealer Price
1966 Mercury CycloneV8-7.0LService typeBrake Pads - Rear ReplacementEstimate$265.31Shop/Dealer Price$319.04 - $452.33
1967 Mercury CycloneV8-6.4LService typeBrake Pads - Rear ReplacementEstimate$245.31Shop/Dealer Price$299.06 - $432.36
1968 Mercury CycloneV8-4.7LService typeBrake Pads - Rear ReplacementEstimate$245.31Shop/Dealer Price$299.06 - $432.36
1966 Mercury CycloneV8-4.7LService typeBrake Pads - Rear ReplacementEstimate$245.31Shop/Dealer Price$299.04 - $432.32
1968 Mercury CycloneV8-7.0LService typeBrake Pads - Rear ReplacementEstimate$245.31Shop/Dealer Price$299.07 - $432.39
1969 Mercury CycloneV8-7.0LService typeBrake Pads - Front ReplacementEstimate$245.31Shop/Dealer Price$299.06 - $432.36
1967 Mercury CycloneV8-4.7LService typeBrake Pads - Rear ReplacementEstimate$250.31Shop/Dealer Price$303.92 - $437.12
1971 Mercury CycloneV8-6.6LService typeBrake Pads - Rear ReplacementEstimate$250.31Shop/Dealer Price$304.29 - $437.78
Show example Mercury Cyclone Brake Pad Replacement prices

Brake Pad Replacement Service

What are brake pads and how do they work?

Brake pads consist of friction material that is bonded to a sturdy steel backing plate. When you push on the brake pedal, the friction material on the brake pads is forced against the inner and outer surfaces of the steel brake rotor under tremendous pressure. The resulting friction causes the wheels on your car to slow rapidly allowing for a quick, safe and controlled stop. After thousands of miles, this friction material eventually wears away, and the brake rotor wears away as well, requiring replacement.

Brakes-Service

When to replace brake pads?

Here are several indications that you need new brake pads:

  • Wear indicator on vehicle dashboard. When the friction material on the brake pads is worn to within 2 mm of the pad backing plate, replacement of the pads is necessary. Most newer cars today have electronics built into the brake pad. When the pad is at a point that it needs to be replaced, a symbol will appear on your vehicle dashboard’s instrument cluster. Consult your owner’s manual to learn what the symbol looks like.
  • High pitched squeal when braking. When the friction material on the pads is worn close to the backing plate, you may hear a squealing or squeaking noise as you drive regardless of whether you are applying the brakes or not. That squealing or squeaking noise is designed to make you aware that the brake pads are getting low and need to be inspected. If all of the friction material on the brake pad has been worn away, you will hear grinding and scraping noises when you apply the brakes. Pad replacement is mandatory at this point and the vehicle is unsafe to drive until corrected.
  • Brake pedal pulsation or vehicle vibration. Over time, brake rotors may develop excessive thickness variation (>.001 inches), excessive runout on the wheel hub (> .002 inches), or the brake rotor may warp due to high operating temperatures. If these defects exist, you may notice pulsation in the brake pedal or steering wheel during braking. New pads and rotor resurfacing or replacement will be required if the rotor has any of the above-mentioned deficiencies.
  • Vehicle pulling or wandering on braking. If your car pulls to the right or left during braking, that could be a sign of a sticking brake caliper, misalignment of the suspension, and sometimes tire defects or uneven tire inflation from side-to-side. The mechanic who inspects your vehicle will determine if new brake pads alone will resolve the issue or if other repairs are needed.
  • High mileage on existing pads. Regardless of whether any of the above brake system symptoms occur, every 10,000 miles a mechanic should measure the thickness of the remaining friction material on the brake pads and perform a thorough visual inspection of the braking system.
  • Brake system warning lights and/or maintenance reminder messages. Should your brake system warning light ever illuminates, or a brake system related maintenance reminder message appears in the driver information display, have your vehicle inspected and repaired as soon as possible.

How do mechanics replace brake pads?

Normally, pad replacement requires these steps:

  • Confirm the thickness of the remaining friction material on the brake pads. If the remaining friction material is less than 2 mm in thickness, pad replacement is warranted.
  • Visually inspect the brake rotor surface that contacts the pad (for scoring, pitting, grooves, rust) and measure the brake rotor with precision tools for thickness variation, run-out and warpage.
  • Inspect the caliper, torque plate, pads, and rotors to determine if the caliper is operating freely (i.e., inspect for stuck calipers).
  • Install new pads and any additional recommended components (e.g., rotors, if rotors depart from OEM specifications) only with customer approval of course.
  • Lubricate brake system components, such as caliper sliding pins, and inspect the condition of the brake fluid. Top off brake fluid as required.
  • Perform a basic 50 point safety inspection of your vehicle.
  • Finally, the mechanic will test drive your vehicle to confirm normal operation of the brake system.

Is it safe to drive with a brake pad problem?

Driving a vehicle with a known deficiency in the braking system is unsafe and consequently is not recommended. Worn out brake pads can increase stopping distances and so for your safety, it is always advised that worn out brake pads be replaced promptly. Further driving is not recommended and you should request service at your earliest convenience if any of the following circumstances exist: stopping distances are much greater than what you are accustomed to; the brake pedal is not firm or is low; there is loss of braking power assist; the vehicle pulls severely to one side on braking; or the brake system warning light is on.

If you detect unusual noises, such as squealing or grinding, but stopping distances are close to what you are used to, and the brake pedal is firm, and there are no warning lights, it may be safe to proceed to your destination but schedule service at your earliest convenience. When it comes to the brakes on your vehicle, always err on the side of caution and have a mechanic check your brake pads and braking system at the first indication of a problem.

When replacing brake pads keep in mind:

Brake pads must always be replaced as a set, that is both wheels (driver and passenger side) on an axle, front or rear, must be serviced. If brake pads on only one side of the car were replaced, your car might pull to one side when you apply the brakes. Often, resurfacing or replacement of the brake rotors is necessary and a competent mechanic will always measure for wear and damage to the brake rotors and advise you as to whether rotor replacement or re-surfacing is needed.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercury mechanics

Real customer reviews from Mercury owners like you.

Excellent Rating

(76)

Rating Summary
74
2
0
0
0
74
2
0
0
0

Patrick

33 years of experience
1377 reviews
Patrick
33 years of experience
Mercury Sable V6-3.0L - Brake Pads Replacement (Front) - Austin, Texas
Patrick is fantastic. His customer service and mechanical acumen is the best I've ever experienced in this industry.

Frederick

16 years of experience
54 reviews
Frederick
16 years of experience
Mercury Mariner V6-3.0L - Brake Pads Replacement (Front) - Emeryville, California
Frederick called me the day before to confirm the appointment and then 20 minutes before he arrived. He fixed 2 of my brakes, test drived and left in less than 1 hour! Great service overall. I will definitely work with him again in the future.

Refugio

17 years of experience
51 reviews
Refugio
17 years of experience
Mercury Mountaineer V6-4.0L - Brake Pads Replacement (Rear) - Universal City, Texas
arrived on time; very friendly; fast service about an hours work; vehicle runs smooth now; very easy transaction process

AUDIE

33 years of experience
191 reviews
AUDIE
33 years of experience
Mercury Grand Marquis V8-4.6L - Brake Pads Replacement (Front) - Henderson, Nevada
Great guy, very professional, cares about his work. Audie will be my mechanic when one is needed in the future.

Excellent Rating

(76)

Rating Summary
74
2
0
0
0
74
2
0
0
0
Number of Mercury Brake Pads Replacement services completed
836+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercury MECHANICS
600+
experts on our platform

Recent articles & questions

Colorado Parking Laws
Colorado Colorado parking laws: understanding the basics Many drivers in Colorado are well aware of the regulations and laws when they are out driving on the roads. However, they may not be quite as familiar with the laws regarding parking....
Ram Certified Pre-Owned (CPO) Car Program
Drivers Drivers in the market for a used Ram vehicle may want to check out cars under their certified pre-owned program. Many manufacturers have a certified pre-owned (CPO) program, and each one is set up differently. Read on to learn...
B1326 OBD-II Trouble Code: Door Ajar Lamp Circuit Short to Ground
B1326 means there is a circuit error with the door ajar lamp, likely due to a defective door ajar switch, defective door switch, or short circuit.

How do I install the head restraints?

It is very easy to install the heat restraints after you have removed them. To do so, simply place the restraint legs into the installation holes, and push down until the restraint locks into place. Then press and hold the...

When A/C is on, the car overheats

Engine overheating with AC on is generally caused by one of two possibilities. One, is increased engine load caused by a failing AC compressor. The AC compressor adds rotational load to the engine and if the compressor is wearing and...

How do you know when evaporative emission vapor vent tube from fuel tank to evaporative emission canister is faulty?

If a leak in the EVAP system is detected, the Check Engine light will illuminate on the dash and the trouble code related to the problem will be stored in the engine computer. When an air leak is present in...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com