Mercedes-Benz SL500 Power Steering Pump Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Power Steering Pump Replacement Service

How much does a Power Steering Pump Replacement cost?

On average, the cost for a Mercedes-Benz SL500 Power Steering Pump Replacement is $742 with $406 for parts and $336 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1996 Mercedes-Benz SL500V8-5.0L	Service typePower Steering Pump Replacement	Estimate$1640.80	Shop/Dealer Price$1960.14 - $2878.47
2001 Mercedes-Benz SL500V8-5.0L	Service typePower Steering Pump Replacement	Estimate$1163.30	Shop/Dealer Price$1374.23 - $1989.69
1994 Mercedes-Benz SL500V8-5.0L	Service typePower Steering Pump Replacement	Estimate$2600.47	Shop/Dealer Price$3067.74 - $4429.30
2004 Mercedes-Benz SL500V8-5.0L	Service typePower Steering Pump Replacement	Estimate$1457.72	Shop/Dealer Price$1742.35 - $2578.71
2002 Mercedes-Benz SL500V8-5.0L	Service typePower Steering Pump Replacement	Estimate$1163.30	Shop/Dealer Price$1380.52 - $2000.70
2006 Mercedes-Benz SL500V8-5.0L	Service typePower Steering Pump Replacement	Estimate$1457.72	Shop/Dealer Price$1742.94 - $2579.74
1998 Mercedes-Benz SL500V8-5.0L	Service typePower Steering Pump Replacement	Estimate$1615.57	Shop/Dealer Price$1926.45 - $2838.44
1995 Mercedes-Benz SL500V8-5.0L	Service typePower Steering Pump Replacement	Estimate$2600.47	Shop/Dealer Price$3067.72 - $4429.27

Show example Mercedes-Benz SL500 Power Steering Pump Replacement prices

What is the power steering pump and how does it work?

The power steering pump is a belt-driven or electric-driven hydraulic pump that generates the hydraulic pressure needed to provide power steering assist. It develops output pressures of 1,000 PSI or more. The pump output is directed to the steering gear, often a rack and pinion type unit, where the hydraulic pressure pushes on the steering rack, greatly reducing the effort it would otherwise take to turn the steering wheel.

Power Steering

When to consider replacing the power steering pump:

Groaning or whining noise when turning. Noise can occur if there is wear on the pump bearings or impeller vanes. A low fluid level or trapped air can also cause noises. If the pump has already been operating while dry, adding fluid may not resolve the noise and replacement of the pump might be necessary.
Power steering fluid leaks. Leaks can develop at pump seals, threaded connections, hoses, or on the steering rack and pinion unit. Pump seal leaks will generally require a replacement.
Difficult steering. Should you notice it is harder to turn the steering wheel, it might mean the power steering pump output pressure is too low, or there could be blockages in the pump or lines.
Damage to the pump pulley. Should the pump pulley become damaged or is loose on the pump shaft, you might detect vibration, drive belt damage, or hard steering. Either the pulley will have to be serviced or the pump assembly replaced.

How do mechanics replace the power steering pump?

If driven by a drive belt, the power steering pump is bolted to the engine via a bracket that allows for adjustment of the pump drive belt. Once the engine is cold, and safe to work on, the drive belt is removed.
If driven by an electric pump, the pump may be mounted in conjunction with the steering shaft or in conjunction with the steering rack. With either a drive belt or electric pump, removal of any dash, panel, or steering components is performed to access the pump.
The threaded connectors to the pump inlet and outlet are loosened and removed.
Any mounting bolts and brackets are removed so the pump can be removed.
If the old pump has failed catastrophically, or there is reason to suspect contaminants in the power steering hoses, the system is flushed.
The new pump is bolted on, the pressure and return hoses attached and the system is bled of all air. If pump is belt-driven, it is tightened to the manufacturer’s specification.
Finally, the engine is run and the car is road tested to confirm normal steering effort. If a new drive belt was installed, belt tension is measured again, and adjusted as needed, after the belt has run for a few minutes.

Is it safe to drive with a power steering pump problem?

No. If the power steering pump is operated without an adequate amount of fluid, and the pump reservoir will not hold fluid due to a large leak. The pump could seize, which would snap the serpentine belt and likely leave you stranded. If the pump turns and there is adequate fluid, but there is no power assist, it will require much greater effort to turn the steering wheel, and that presents inherent safety risks. Generally, the wisest course is to seek immediate repairs if you suspect a problem with any component in your car’s power steering system.

When replacing the power steering pump keep in mind:

Any belts driving the pump should be inspected and replaced as needed. The pump will only produce the required hydraulic pressure if it is driven by the belt at an adequate speed.
Power steering leaks from aged rubber hoses, particularly where the rubber is crimped to the steel tube, are not unusual and should be carefully inspected. The system operates under high pressure. The fluid is flammable, and if leaking fluid happens to contact a hot engine part, a fire might result. You always want to be sure the hoses and connections are sound.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(99)

Rating Summary

92

7

0

0

0

92

7

0

0

0

SEE REVIEWS NEAR ME

Michael

16 years of experience

32 reviews

Request Michael

Michael

16 years of experience

Request Michael

by Thomas Galloway

SL500 2005 - Electric Problems - Hillcrest Heights, MD

Good

Michael

19 years of experience

168 reviews

Request Michael

Michael

19 years of experience

Request Michael

by William Graham

SL500 2002 - Spark Plugs - Fontana, CA

this guy is alright he did a very good job

Rafael

25 years of experience

65 reviews

Rafael

25 years of experience

by Jack Headley

SL500 1994 - Brake Pads - South San Francisco, CA

Great work

Raymond

35 years of experience

252 reviews

Request Raymond

Raymond

35 years of experience

Request Raymond

by Sergio Ramirez

SL500 2001 - Fuel Filter - Las Vegas, NV

Outstanding!

Excellent Rating

(99)

Rating Summary

92

7

0

0

0

92

7

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

Symptoms of a Bad or Failing Windshield Wiper Switch

Common signs include windshield wipers not turning on or off, not changing speed or settings, and the turn signals not working.

Acura Certified Pre-Owned (CPO) Car Program

Drivers Drivers in the market for a used Acura vehicle may want to check out cars under their certified pre-owned program. Many manufacturers have a certified pre-owned (CPO) program, and each one is set up differently. Read on to learn...

Cell Phones and Texting: Distracted Driving Laws in Minnesota

Minnesota Minnesota defines distracted driving as anything that distracts the driver from the primary task of driving and increases the risk of an accident. Distracted driving is a factor in one out of every four car accidents. This causes 350...

Shaking issue when accelerating 45-55 and 60-75 and areas between. (2007 Acura TSX manual transmission)

What you are describing does sound like a bad inner C/V joint or joints. Even if the C/V boot is not torn and all the grease thrown out like typically happens with outer C/V boots, inner C/V boots (https://www.yourmechanic.com/services/cv-boot-replacement) can...

Windshield wiper linkage

Hello, thank you for writing in. It is likely they were not installed correctly. It may be that they were left loose, or any number of other installation issues. Typically installing wiper blades is straight forward and easy. The best...

Accelerate

You may be having an engine misfire. If your check engine light is on then have a computer scan to see what codes are stored to find the cylinder that is misfiring and may need spark plugs and ignition coils...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com