Mercedes-Benz CLS400 Front Crankshaft Seal Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(6)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(6)

Front Crankshaft Seal Replacement Service

How much does a Front Crankshaft Seal Replacement cost?

On average, the cost for a Mercedes-Benz CLS400 Front Crankshaft Seal Replacement is $271 with $14 for parts and $256 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2016 Mercedes-Benz CLS400V6-3.0L TurboService typeFront Crankshaft Seal ReplacementEstimate$339.45Shop/Dealer Price$393.96 - $451.13
Show example Mercedes-Benz CLS400 Front Crankshaft Seal Replacement prices

What is the Front Crankshaft Seal all about?

A number of mechanisms must work together to make your vehicle move forward. One of the most important is the crankshaft, which converts rotary into linear motion; i.e., it transforms the force created by the engine's pistons moving up and down into a force that moves in a circular motion that causes a car’s wheel to turn. Enclosed in what’s called a crankcase—the largest cavity in the engine block, just below the cylinders—the crankshaft must be completely lubricated, essentially submerged in oil, to spin nearly friction-free and do its job properly.

Consequently, there are seals located at either end of the crankshaft that allow it to spin freely and keep engine oil from escaping the engine block, as well as prevent contaminants and other debris from entering and causing damage to the mechanism. Since there are two ends of the crankshaft, there are two types of seals: the front crankshaft seal and the rear crankshaft seal, also known as the front main and rear main seals.

Keep in mind:

  • Loss of oil will eventually cause serious internal engine damage.
  • Inspect the sealing surface of the crankshaft or the crankshaft pulley (depending on the engine design) for damage when replacing the crankshaft seal.
  • Oil degrades rubber components.

How it's done:

  • The vehicle is raised and supported on jack stands
  • The crankshaft damper and timing belt is removed
  • The crankshaft seal is removed and a new one installed
  • The timing belt and cover along with crankshaft damper is reinstalled
  • The engine accessory belts are installed and the vehicle is lowered off of the jack stands

Our recommendation:

One of the most important parts of your car, crankshaft seals are typically made from a durable material, such as a synthetic rubber or silicone, designed to handle the extreme pressure and temperatures as well as the caustic chemicals in your engine oil. Because they are exposed to such abuse, main seals are subject to a lot of wear and tear. And whether you are talking a front or rear main seal, replacement is the only cure when one malfunctions.

The good news is that the seals are relatively inexpensive components. The bad news is that neither is easy to replace.

Front seal: The front seal is located behind the main pulley that drives all the belts, which is, of course, always spinning. The main pulley throws any leaking oil out in a big circle. It can get thrown up on the alternator, steering pump, belts, in short anything attached to the front of the engine and cause a real mess and eventually some serious damage. Consequently, it has to be removed along with many of the components attached to the front of the block to replace the front main seal.

Rear seal: The rear crankshaft seal is placed along with the transmission; therefore, the process of replacing it requires the removal of transmission, as well as the clutch and flywheel assembly. This is a very involved job.

What common symptoms indicate you may need to replace the Front Crankshaft Seal?

  • Oil leaking from the front crank pulley.
  • Oil dripping from the bottom of the clutch housing, where the block and transmission meet.
  • Clutch slip caused by oil spraying on the clutch.

How important is this service?

Letting either crankshaft seal continue to leak can be detrimental to your vehicle’s continued operation. Besides the maladies caused by driving around with little to no oil flowing in the engine, the faulty seal will be spread oil through the engine bay and undercarriage of your car as you drive, a mess that is difficult to clean up and can be a fire hazard. Replacing is better addressed sooner than later.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(6)

Rating Summary
5
0
0
0
1
5
0
0
0
1

David

13 years of experience
393 reviews
David
13 years of experience
Mercedes-Benz CLS400 V6-3.0L Turbo - Oil Change - Marietta, Georgia
Always deliver!!!! Awesome experience!

Casey

19 years of experience
61 reviews
Casey
19 years of experience
Mercedes-Benz CLS400 V6-3.0L Turbo - Car Battery Replacement - Sugar Land, Texas
Casey was right on time and finished very quickly. Great experience!

David

13 years of experience
393 reviews
David
13 years of experience
Mercedes-Benz CLS400 V6-3.0L Turbo - Brake Pads Replacement (Front) - Marietta, Georgia
David continues to DELIVER!!!!

Tinashe

13 years of experience
605 reviews
Tinashe
13 years of experience
Mercedes-Benz CLS400 V6-3.0L Turbo - Oil Change - Marietta, Georgia
Delivers every time! I can always count on this guy.

Excellent Rating

(6)

Rating Summary
5
0
0
0
1
5
0
0
0
1
Number of Mercedes-Benz CLS400 services completed
66+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

Top 10 Scenic Drives in South Dakota
South Dakota may not get a lot of play outside of seeing Mount Rushmore as a tourist destination, but that doesn’t mean there isn’t an array of recreational opportunities and scenic views. It just means the state’s most treasured areas...
P0307 OBD-II Trouble Code: Cylinder 7 Misfire Detected
P0307 code definition Cylinder 7 Misfire Detected What the P0307 code means When the P0307 diagnostic trouble code is stored by the...
P2175 OBD-II Trouble Code: Throttle Actuator Control System Low Airflow Detected
P2175 P2175 code definition Throttle Actuator Control System Low Air Flow Detected What the P2175 code means P2175 is an OBD-II generic code for the engine control module (ECM) detecting that the air flow into the engine was not at...

My truck over heated then it shut off the heat is blowing cold air

Hi there: In most cases, the overheating and heater blowing cold air issue is related to an obstruction within the heater core that needs to be removed or repaired. This can be done by flushing the cooling system, removing coolant...

What type of Ball Joint System does a 2005 Nissan Altima Have? Or where can I find this information ? 2005 Nissan Altima

Hello - the front suspension on your Altima utilizes a lower control arm (https://www.yourmechanic.com/question/when-replacing-ball-joints-can-you-just-replace-the-ball-joints-or-do-you-have-to-replace-the-whole-control-arm-by-debra-l) (with a pressed in ball joint), and a strut/spring assembly. The ball joint comes pressed into the aluminum lower control arm, and is generally not available...

Car engine sounds like vacuum cleaner.

The issue sounds like the timing belt is put on 180 degrees off making the exhaust the open when trying to start and the intake open when trying to compression. This will cause a vacuum sucking sound as the vehicle...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com