Mercedes-Benz C400 Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(5,647)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(5,647)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mercedes-Benz C400 Brake Drum Replacement is $530 with $369 for parts and $161 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2015 Mercedes-Benz C400V6-3.0L TurboService typeBrake Drum ReplacementEstimate$933.02Shop/Dealer Price$1147.16 - $1722.63
Show example Mercedes-Benz C400 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(5,647)

Rating Summary
5,256
190
54
28
119
5,256
190
54
28
119

Nazareth

27 years of experience
285 reviews
Nazareth
27 years of experience
Mercedes-Benz C400 V6-3.0L Turbo - Car Battery Replacement - Glendora, California
He was very fast and his prices are extremely reasonable

Charles

34 years of experience
342 reviews
Charles
34 years of experience
Mercedes-Benz C400 V6-3.0L Turbo - Back To School Promo - Austin, Texas
He has done a great job in the timely manner. I would definitely recommend him.

Andrew

11 years of experience
859 reviews
Andrew
11 years of experience
Mercedes-Benz E320 V6-3.2L - Air Springs Replacement (Driver Side Rear) - Shawnee Mission, Kansas
Andrew was great! He explained everything thoroughly and showed me everything that was to be done. Great personality and very trust worthy with my classic Mercedes-Brenz. Felt very safe with his work. I'll be calling again for any other work!

Joe

15 years of experience
453 reviews
Joe
15 years of experience
Mercedes-Benz E550 V8-5.5L - Pre-purchase Car Inspection - Nashville, Tennessee
Helpful

Excellent Rating

(5,647)

Rating Summary
5,256
190
54
28
119
5,256
190
54
28
119
Number of Mercedes-Benz services completed
62117+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

Top 10 Scenic Drives in Iowa
When you think about Heartland America, Iowa likely comes to mind. The state is known for its rural farmlands with fields of corn and small communities that seemingly spring up out of nowhere. While this is definitely a part of...
How Long Does an AC Compressor Relay Last?
Your Your car’s air conditioning system needs to be able to pressurize refrigerant in order to operate. The AC compressor relay is an electronic component that turns your AC compressor off and on. Without it, the compressor will not work,...
P0727 OBD-II Trouble Code: Engine Speed Input Circuit No Signal
P0727 code means that the engine speed input sensor is not properly functioning often due too corroded wires or defective shift solenoids.

Car charging port/cigarette lighter not working

The first thing to check is the fuse. Blown fuses can be the result of a problem with the charging socket, or wiring. Look at the socket closely to check for foreign objects or loose contacts. However, do not overlook...

Orange light came on securityty and service vehicle soon drove 5 miles and air was hot and tried to put window down but they woul

Hi there. Quite frequently a security system error like you've described will be caused by an electrical short somewhere in the vehicle. This may be the reason why the mechanic was unable to find the root issue. In most cases,...

my 2005 cadillac escalade wont shift out of first gear what can be the problem

Hi there. Thanks for your email to YourMechanic.com's Ask a Mechanic. In most cases, when a transmission will not shift out of first gear, it is due to one of two things. First, and most common; is due to dirty...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com