Jeep Wrangler JK Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(7)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(7)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Jeep Wrangler JK Brake Drum Replacement is $370 with $208 for parts and $161 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2018 Jeep Wrangler JKV6-3.6LService typeBrake Drum ReplacementEstimate$611.64Shop/Dealer Price$732.69 - $1057.56
Show example Jeep Wrangler JK Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Jeep mechanics

Real customer reviews from Jeep owners like you.

Excellent Rating

(7)

Rating Summary
7
0
0
0
0
7
0
0
0
0

Davin

27 years of experience
23 reviews
Davin
27 years of experience
Jeep Wrangler JK V6-3.6L - Car is not starting - Denver, Colorado
Quick knowledgeable and offered to help

Brett

25 years of experience
213 reviews
Brett
25 years of experience
Jeep Wrangler JK V6-3.6L - Brake Pads Replacement (Rear) - Fort Mill, South Carolina
Brett was timely and professional. He was knowledgeable and showed me the parts that needed replacing. Great experience.

Elias

14 years of experience
115 reviews
Elias
14 years of experience
Jeep Wrangler JK V6-3.6L - Oil Change - Teterboro, New Jersey
Elias has worked on my car twice, always professional, shows up on time, and does great work.

Roberto

12 years of experience
307 reviews
Roberto
12 years of experience
Jeep Wrangler JK V6-3.6L - Car is not starting - Houston, Texas
Great

Excellent Rating

(7)

Rating Summary
7
0
0
0
0
7
0
0
0
0
Number of Jeep Wrangler JK services completed
77+
services done by our mechanics
TOTAL NUMBER OF EXPERT Jeep MECHANICS
1300+
experts on our platform

Recent articles & questions

P2161 OBD-II Trouble Code: Vehicle Speed Sensor B Intermittent/Erratic
P2161 P2161 trouble code definition Vehicle Speed Sensor B Intermittent/Erratic What the P2161 code means P2161 is an OBD-II generic code for the engine control module (ECM) detecting the vehicle speed sensor 2 or B giving an intermittent or erratic...
How to Put a Sunroof in Your Car
One of the most popular vehicle options in recent years are sunroofs. There are several styles in the marketplace including sliding glass sunroofs, tilting sunroofs, and panoramic sunroofs. A sunroof can either be manually operated or motorized with an electric...
How to Rent a Car in Europe
When When you’re planning a trip through Europe, it might be a good idea (and also may be the most cost-effective) to consider renting a car if you plan on doing a lot of sightseeing and exploring. Probably one of...

ABS light and traction control come on while driving, go away after restart.

I would have the car scanned with an ABS scan tool (https://www.yourmechanic.com/services/abs-light-is-on-inspection) to have the problem diagnosed.

Do I risk a car fire? I have a small oil leak in my car.

There is a very small chance that a slight oil leak would cause a complete engine fire. The oil that is leaked onto the engine will burn, and cause smoke as the result, but this is not the same as...

The car will crank but won't turn over

If the starter motor is turning the engine over rapidly, at sufficient RPM, but the engine does not catch and run, that means that there is an ignition, fuel, air induction, or mechanical fault in the engine that will have...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com