Isuzu i-350 Coolant Temperature Switch (Sensor) Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(313)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(313)

Coolant Temperature Switch (Sensor) Replacement Service

How much does a Coolant Temperature Switch (Sensor) Replacement cost?

On average, the cost for a Isuzu i-350 Coolant Temperature Switch (Sensor) Replacement is $191 with $48 for parts and $142 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2006 Isuzu i-350L5-3.5LService typeCoolant Temperature Switch (Sensor) ReplacementEstimate$268.67Shop/Dealer Price$307.71 - $391.10
Show example Isuzu i-350 Coolant Temperature Switch (Sensor) Replacement prices

What is the Coolant Temperature Switch (Sensor) all about?

The coolant temperature switch, also called the coolant temperature sensor, is a switch that reads the engine coolant temperature and sends a signal to the engine control module, or ECM, to control other functions of engine operation such as the air-fuel ratio.

It is also called a switch because on some cars, it is used to turn on the engine cooling fan at a specific temperature. This aids in the engine warm-up process as well as keeping the engine at a safe operating temperature.

Keep in mind:

  • The coolant temperature switch is a crucial part of the cooling system. If faulty, it can cause severe internal engine damage due to overheating, incorrect air-fuel ratio, or incorrect ignition timing. It can also cause shorter life to the cooling fan motor or other electrical components of the cooling system.
  • Some vehicles are equipped with a separate sensor to display the engine temperature to the driver via the temperature gauge.

How it's done:

  • The Coolant Temperature Switch is verified that it needs to be replaced. The coolant is drained until the switch is exposed.

  • The defective Coolant Temperature Switch is removed by disconnecting the connector and removing it from the manifold.

  • The new Coolant Temperature Switch is installed into the mounting hole in the manifold and the electrical connector is reconnected. The coolant is then refilled.

  • The Coolant Temperature Switch is tested for operation, codes cleared, and retested to ensure all codes have been resolved.

  • The vehicle is road tested to ensure proper operation of the Cooling System.

Our recommendation:

If you suspect that your coolant temperature switch has failed, have one of our licensed mechanics come out immediately to diagnose the problem.

What common symptoms indicate you may need to replace the Coolant Temperature Switch (Sensor)?

  • Check Engine light on
  • Engine overheating
  • Cooling fan runs intermittently
  • Engine misfires, stalls, or idles roughly
  • Erratic coolant temperature

How important is this service?

This part, when faulty, could cause the fan to run intermittently or not at all, which in turns causes overheating or overuse of the cooling fan motor. Whenever overheating occurs, severe engine damage is a possibility.

The engine air-fuel ratio is what keeps it running smoothly. If the ratio gets skewed, the engine will have poor fuel economy and run poorly or not at all. The coolant temperature switch is important because it gives the ECM the information it needs to make this calculation and run the engine optimally. YourMechanic will be able to tell you if this part is performing correctly.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Isuzu mechanics

Real customer reviews from Isuzu owners like you.

Excellent Rating

(313)

Rating Summary
290
13
0
2
8
290
13
0
2
8

Ralph

38 years of experience
187 reviews
Ralph
38 years of experience
Isuzu Rodeo V6-3.2L - Alternator - Seattle, Washington
Early for the appointment, professional, fast, excellent, thank you very much.

Richard

35 years of experience
104 reviews
Richard
35 years of experience
Isuzu Rodeo V6-3.2L - Exterior Door Handle Replacement (Driver Side Front) - Zephyrhills, Florida
Arrived early and did the job in 20 minutes. Impressed! Will use again. Very open and friendly.

David

18 years of experience
44 reviews
David
18 years of experience
Isuzu Rodeo L4-2.2L - Car is not starting - Dallas, Texas
Very friendly professional

Jonathan

22 years of experience
304 reviews
Jonathan
22 years of experience
Isuzu Trooper V6-3.2L - Oxygen Sensor Replacement (Front/Upper/Upstream) - Denver, Colorado
Very good,fast and easy, Jonathan was great

Excellent Rating

(313)

Rating Summary
290
13
0
2
8
290
13
0
2
8
Number of Isuzu services completed
3443+
services done by our mechanics
TOTAL NUMBER OF EXPERT Isuzu MECHANICS
200+
experts on our platform

Recent articles & questions

Rules of the Road For Ohio Drivers
When When it comes to driving, if you have a valid driver’s license, you likely know the traffic laws you are required to follow in the state in which it was issued. While that same knowledge will help with the...
10 Best Stores to Buy Auto Parts in Hartford, Connecticut
Automotive technicians rely on auto parts stores to add and replace car parts. The best auto parts shop in Hartford is Napa Auto Parts.
What Does the Electronic Stability Control (ESC) Warning Light Mean?
The ESC warning light is designed to help drivers in case they lose steering control by retaining control of the brakes and engine power in the car.

Reocurring wheel speed sensor failure

Hey there. As you may know, these sensors monitor wheel speed for a variety of the car's onboard systems such as the traction control, ABS, and other systems. When wheel speed sensors (https://www.yourmechanic.com/services/wheel-speed-sensor-replacement) go bad, they can cause many problems...

What else should I do?

The fuel injectors on this engine can intermittent stick causing a misfire. The fix is to replace the injector for the cylinder having the problem. This is from a carbon build up in the injector pintle. I would recommend having...

I replaced my clutch and bleed my hydraulic clutch master cylinder. But when I put the truck in 2H and try to shift, I won't shift.

Hi there. There seems to be an issue with the transfer case on your vehicle. The transfer case may have a bent fork or the shifter synchronizer has broken teeth. I recommend seeking out a professional, such as one from...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com