Isuzu i-280 Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(312)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(312)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Isuzu i-280 Brake Drum Replacement is $512 with $284 for parts and $228 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2006 Isuzu i-280L4-2.8LService typeBrake Drum ReplacementEstimate$843.08Shop/Dealer Price$1008.85 - $1452.18
Show example Isuzu i-280 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Isuzu mechanics

Real customer reviews from Isuzu owners like you.

Excellent Rating

(312)

Rating Summary
289
13
0
2
8
289
13
0
2
8

Corey

27 years of experience
43 reviews
Corey
27 years of experience
Isuzu i-280 L4-2.8L - Car is not starting - Kennesaw, Georgia
Extremely knowledgeable and very honest!!

Corey

27 years of experience
43 reviews
Corey
27 years of experience
Isuzu i-280 L4-2.8L - Brake Light Switch - Kennesaw, Georgia
Corey did an awesome job!

Peter

43 years of experience
1321 reviews
Peter
43 years of experience
Isuzu Rodeo V6-3.2L - Brake Drum Replacement - Phoenix, Arizona
I have already referred someone to you for a quote.

Scott

36 years of experience
899 reviews
Scott
36 years of experience
Isuzu Rodeo V6-3.2L - Car Radiator Replacement - Phoenix, Arizona
Scott was punctual and very polite, as well as informative about the problems with my vehicle. You guys must be the luckiest company in the world to have a staff of mechanics that are so professional and courteous!!! What? Are you guy's cloning them in some awesome machine? LOL!!! GREAT JOB GUYS!!!!

Excellent Rating

(312)

Rating Summary
289
13
0
2
8
289
13
0
2
8
Number of Isuzu services completed
3432+
services done by our mechanics
TOTAL NUMBER OF EXPERT Isuzu MECHANICS
200+
experts on our platform

Recent articles & questions

What Is Brake Dust?
It's It's time to wash the car, but when you get to the wheels they are covered by a hard to remove gray dust. Even after you clean it off, it comes back quickly. Welcome to the world of brake...
How to Transfer a Car Title in Montana
Montana Montana requires that all vehicles in the state have a title in the name of the owner. When ownership changes, either through a sale, gifting, inheritance, or through a simple name change, the title needs to be transferred. The...
How to Check the Choke on a Carbureted Engine
The The choke is a plate in the carburetor (https://www.yourmechanic.com/article/how-does-the-carburetor-work-within-the-fuel-system) that opens and closes to allow more or less air into the engine. Similar to the throttle, the choke plate rotates from a horizontal to vertical position to open up...

Chain needs to be replaced

The reason a timing chain can take so long at a shop is because of the large amount of labor that it entails to perform a repair of that caliber. Many parts will need to be removed in order to...

My car sputters and the Check Engine Light starts flashing after it rains.

When the Check Engine Light flashes, this can mean that the catalytic converter may be flooded with fuel and that a fire hazard exists. Because your car is sputtering, I believe this condition exists for you. When a car sputters...

Will only driving short distances damage my car's engine?

Hi there. Short trips do not damage a vehicle as long as the engine is allowed to reach operating temperature. I'm not sure where this myth originated, but it is tied to older vehicles that used to develop engine "run...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com