GMC Sierra 1500 Limited Transfer case fluid is low Inspection at your home or office.

Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.

Estimate price near me

Service Location

Customer Ratings

(2,958)

How A Diagnostic Works

Instantly book a certified mobile mechanic to come to you

Mechanic diagnoses the problem and quotes necessary repairs

Your vehicle is ready to go

Fair, upfront & transparent pricing for all services

Our certified mobile mechanics can come to you now.

Customer Ratings

(2,958)

Transfer case fluid is low Inspection Service

How much does a Transfer case fluid is low Inspection cost?

On average, the cost for a GMC Sierra 1500 Limited Transfer case fluid is low Inspection is $95 with $0 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2019 GMC Sierra 1500 LimitedV8-5.3LService typeTransfer case fluid is low InspectionEstimate$114.99Shop/Dealer Price$124.99 - $132.49
Show example GMC Sierra 1500 Limited Transfer case fluid is low Inspection prices

If you have a four-wheel drive or an all-wheel drive car, you have more than just the engine and the transmission to worry about. You also have a transfer case, which is responsible for sending power from the transmission to all four wheels via drive shafts. If your transfer case fluid is low, there’s a problem that should be repaired before you can safely drive.

How this system works:

A transfer case does exactly what the name implies – it transfers power from the transmission to the wheels. However, it will work differently depending on the type of vehicle you drive. If you drive a four-wheel drive truck, then the primary wheels are driven by the driveshaft and the transfer case really only comes into play when you engage four-wheel drive mode. However, if you have an all-wheel drive vehicle, or an all-time four-wheel drive system, then the transfer case will be used at all times (because all four wheels must work at once, at all times).

The transfer case mounts to the end of the transmission, and a shaft extends from the transmission into the transfer case. Inside the transfer case, there are internal forks and gears that are responsible for transmitting the rotational power of the transmission to two other drive shafts – one going to the rear differential, and another going to the front differential. Within each differential, rotational power is split again, and redirected at 90 degrees to each wheel.

Common reasons for this to happen:

  • Leaking Input Seal at Transmission: If you’re experiencing low transfer case fluid, one of the first possible problems to consider is the input seal on the transmission side of things. Over time and through normal wear and tear, these seals will degrade, eventually letting fluid seep out.

  • Leaking Output Shaft Seal Rear: Another potential problem is the output shaft seal where the rear drive shaft attaches to the transfer case. Like the input seal on the transmission side, this one can also wear to the point that it begins to leak.

  • Leaking Output Shaft Seal Front: You have one other potential seal that might be leaking. This one is located where the front drive shaft connects with the transfer case. Like the other two we’ve mentioned, this seal will eventually degrade and begin to leak.

  • Leaking Vent Hose: While unlikely, it’s possible that you’re losing transfer case fluid from the vent hose.

  • Failed Speed Sensor Gasket: If your transfer case is equipped with a speed sensor, it’s possible that you’re leaking fluid around the sensor (the seal has failed).

  • Leaking Transfer Case Gasket: The transfer case gasket is a lot like an oil pan gasket in that it will eventually degrade to the point that it begins to leak fluid (all gaskets and seals on your vehicle are subject to wear, leakage and eventual failure).

What to expect:

A top-rated mobile mechanic will come to your home or office to inspect the leak from your transfer case, as well as the condition of all seals and the level of your fluid. The mechanic will then provide a detailed inspection report that includes the scope and cost of the necessary repairs.

How it's done:

The mechanic will inspect the transfer case first to determine the location of the leak. It may be necessary to clean old fluid from the transfer case and then test drive the vehicle to determine the actual source of the leak. The mechanic will also check the level of fluid.

How important is this service?

If your transfer case is leaking, the internals are in danger of experiencing high heat and friction. Just like your differentials and your transmission, the moving parts within the transfer case must be lubricated properly at all times, or damage will result (depending on the setup of your vehicle, damaged transfer case components could leave the vehicle unable to be driven). One of our professional mechanics can inspect your transfer case, determine the point of the leak, and repair the problem.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert GMC mechanics

Real customer reviews from GMC owners like you.

Excellent Rating

(2,958)

Rating Summary
2,798
79
21
10
50
2,798
79
21
10
50

Adam

21 years of experience
5 reviews
Adam
21 years of experience
GMC Acadia V6-3.6L - Brake Pads Replacement (Front) - Citrus Heights, California
Very efficient and professional. I would not hesitant to utilize Adam again.

Arturo

27 years of experience
303 reviews
Arturo
27 years of experience
GMC Jimmy V6-4.3L - Spark Plugs - San Diego, California
Arturo was professional and knowledgeable. He showed up early and did good work. I will definitely book him in the future if I have car trouble.

Shaun

10 years of experience
542 reviews
Shaun
10 years of experience
GMC Jimmy V6-4.3L - Brake Pads Replacement (Rear) - Phoenix, Arizona
Did a great job on my car.

John

27 years of experience
1019 reviews
John
27 years of experience
GMC Sierra 1500 V8-5.3L - Brake Rotor/Disc Replacement (Front) - Manvel, Texas
I am very happy with the work that John did and everything went exactly as planned. He arrived on time and got the job done in a very professional manner.

Excellent Rating

(2,958)

Rating Summary
2,798
79
21
10
50
2,798
79
21
10
50
Number of GMC services completed
32538+
services done by our mechanics
TOTAL NUMBER OF EXPERT GMC MECHANICS
900+
experts on our platform

Recent articles & questions

How to Buy Good Quality Wheel Bearings
Sometimes Sometimes you can get by with a part on your car being in semi-good condition. That is not the case with wheel bearings. They are responsible for supporting the weight of your car and helping to move the wheels...
Cell Phones and Texting: Distracted Driving Laws in Maryland
Maryland Maryland defines distracted driving as any sensory or cognitive distraction that breaks your focus from the road while operating a vehicle. Sensory distractions can be visual, auditory, or manual. These distractions pose a danger to pedestrians, passengers, and drivers...
P0223 OBD-II Trouble Code: Throttle/pedal position switch/sensor B circuit high output
P0223 P0223 code definition Throttle/Pedal Position Sensor/Switch B Circuit High Input What the P0222 code means The P0222 code is an indication that the Engine Control Module (ECM) has detected voltage from the throttle position sensor to have exceeded the...

how long can it take to change valve cover gaskets on 2003 Lincoln aviator 4.6litre

Hi there. The book time calls for approximately 3.5 hours to complete the replacement of both valve cover gaskets. But this will vary by mechanic, but this is the average book time. If you need to have them replaced, consider...

I feel a thump anytime I hit the smallest dip in the road. I've been told that my control arm or tie end rod needs to be replaced.

Hi there. Raise up your vehicle and check the tie rod ends and the control arms and see if they are damaged or loose. Also check the strut tower and see if they are loose at the top of the...

Shaking

Shaking or vibration (https://www.yourmechanic.com/services/engine-is-shaking-pulsating-or-vibrating-inspection) may be caused by many different things such as faulty spark plugs, poor fuel pressure or misfires. Other things such as a faulty idle air control valve (https://www.yourmechanic.com/services/idle-control-valve-replacement) may cause the engine idle to drop below...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com