Ford F-250 Super Duty Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(287)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(287)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Ford F-250 Super Duty Tie Rod End Replacement is $168 with $73 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2016 Ford F-250 Super DutyV8-6.7L Turbo DieselService typeTie Rod End - Rear Right Inner ReplacementEstimate$640.20Shop/Dealer Price$760.88 - $1075.67
2010 Ford F-250 Super DutyV8-5.4LService typeTie Rod End - Rear Right Outer ReplacementEstimate$344.64Shop/Dealer Price$401.97 - $526.62
2007 Ford F-250 Super DutyV8-5.4LService typeTie Rod End - Front Left Inner ReplacementEstimate$474.54Shop/Dealer Price$569.84 - $817.41
2003 Ford F-250 Super DutyV8-7.3L Turbo DieselService typeTie Rod End - Front Right Outer ReplacementEstimate$322.60Shop/Dealer Price$379.87 - $513.46
1999 Ford F-250 Super DutyV8-7.3L Turbo DieselService typeTie Rod End - Front Right Inner ReplacementEstimate$374.28Shop/Dealer Price$444.54 - $616.93
2006 Ford F-250 Super DutyV8-6.0L Turbo DieselService typeTie Rod End - Front Right Inner ReplacementEstimate$476.10Shop/Dealer Price$571.79 - $820.53
2001 Ford F-250 Super DutyV8-5.4LService typeTie Rod End - Front Left Inner ReplacementEstimate$382.78Shop/Dealer Price$452.78 - $624.98
2016 Ford F-250 Super DutyV8-6.7L Turbo DieselService typeTie Rod End - Front Right Outer ReplacementEstimate$498.78Shop/Dealer Price$592.51 - $825.26
Show example Ford F-250 Super Duty Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(287)

Rating Summary
267
7
3
2
8
267
7
3
2
8

Joel

9 years of experience
58 reviews
Joel
9 years of experience
F-250 Super Duty 2008 - Check Engine Light is on - Lewisville, TX
Best mechanic experience ever! Joel came to the house, at night, in the cold, and went over every inch of my truck. What an amazing service, thank you Joel!

Bill

30 years of experience
52 reviews
Bill
30 years of experience
F-250 Super Duty 2004 - Oil Change - Golden, CO
Bill is an experienced and proficient mechanic! His explanations of the required parts and the necessary service were clear and understandable. I couldn't be more satisfied with Bill's competence!!!!!!!

Nathan

13 years of experience
314 reviews
Nathan
13 years of experience
F-250 Super Duty 2001 - Oil/Fluid Leak - Austin, TX
Nathan was sent to investigate the repairs done by another Your Mechanic tech which we had issues with. He did a great job of fixing the work of the other mechanic and we are very happy.

Dustin

6 years of experience
32 reviews
Dustin
6 years of experience
F-250 Super Duty 2012 - Oil Change - Spring, TX
All good Answered question and ready to do more service!!!

Excellent Rating

(287)

Rating Summary
267
7
3
2
8
267
7
3
2
8
Number of Ford F-250 Super Duty services completed
3157+
services done by our mechanics
TOTAL NUMBER OF EXPERT Ford MECHANICS
1700+
experts on our platform

Recent articles & questions

How to Safely Drive Your Car When It’s Raining
Driving in rainy weather means giving the road your full attention, ensuring you have good tires, and your windshield wipers are effective.
P0249 OBD-II Trouble Code: Turbocharger Wastegate Solenoid B Low
P0249 P0249 code definition The P0249 code indicates that the PCM is detecting an abnormal reading coming from the turbocharger wastegate solenoid “B” circuit. What the P0249 code means Circuit B is a specific wastegate solenoid wherein multiple solenoids are...
How to Replace a Steering Gear Adjuster Plug
Maintaining reliable steering is important for every driver. A common sign of a faulty steering gear adjuster plug is a loose steering wheel.

Clutch pedal going soft after you bleed it. Has s new clutch and a auto shop says it's the master cylinder

Hello. If the clutch pedal is going soft even after it is bled, then that is an indicator that there is either a problem with the master cylinder (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-clutch-master-cylinder) or the slave cylinder (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-clutch-slave-cylinder). If the seals inside the master...

Hello, I have a 2006 mazdaspeed 6 with 100,000 miles and a "blown third piston" is it worth fixing?

It's too bad that it failed this early in the game, but I don't think there's any future in fixing it. Just remember that an engine is only one of many very expensive parts on a car and once you've...

why does my car won't go into gear?

You should check and see with engine off if the clutch slave is moving the clutch when pedal is pressed. If it does not move or take a couple pumps to move then you either have air in system or...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com