Ford E-200 Econoline Brake Pad Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(1,293)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(1,293)

Brake Pad Replacement Service

How much does a Brake Pad Replacement cost?

On average, the cost for a Ford E-200 Econoline Brake Pad Replacement is $197 with $83 for parts and $114 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1971 Ford E-200 EconolineL6-3.9LService typeBrake Pads - Front ReplacementEstimate$303.31Shop/Dealer Price$356.64 - $489.63
1972 Ford E-200 EconolineV8-5.0LService typeBrake Pads - Front ReplacementEstimate$419.35Shop/Dealer Price$507.71 - $745.75
1973 Ford E-200 EconolineL6-3.9LService typeBrake Pads - Front ReplacementEstimate$279.31Shop/Dealer Price$332.66 - $465.66
1970 Ford E-200 EconolineV8-5.0LService typeBrake Pads - Front ReplacementEstimate$419.35Shop/Dealer Price$507.68 - $745.70
1969 Ford E-200 EconolineL6-3.9LService typeBrake Pads - Rear ReplacementEstimate$279.31Shop/Dealer Price$332.68 - $465.70
1974 Ford E-200 EconolineV8-5.0LService typeBrake Pads - Front ReplacementEstimate$419.35Shop/Dealer Price$507.71 - $745.74
1969 Ford E-200 EconolineL6-2.8LService typeBrake Pads - Front ReplacementEstimate$285.31Shop/Dealer Price$338.50 - $471.38
1972 Ford E-200 EconolineL6-4.9LService typeBrake Pads - Front ReplacementEstimate$285.31Shop/Dealer Price$338.94 - $472.16
Show example Ford E-200 Econoline Brake Pad Replacement prices

What are brake pads and how do they work?

Brake pads consist of friction material that is bonded to a sturdy steel backing plate. When you push on the brake pedal, the friction material on the brake pads is forced against the inner and outer surfaces of the steel brake rotor under tremendous pressure. The resulting friction causes the wheels on your car to slow rapidly allowing for a quick, safe and controlled stop. After thousands of miles, this friction material eventually wears away, and the brake rotor wears away as well, requiring replacement.

Brakes-Service

When to replace brake pads?

Here are several indications that you need new brake pads:

  • Wear indicator on vehicle dashboard. When the friction material on the brake pads is worn to within 2 mm of the pad backing plate, replacement of the pads is necessary. Most newer cars today have electronics built into the brake pad. When the pad is at a point that it needs to be replaced, a symbol will appear on your vehicle dashboard’s instrument cluster. Consult your owner’s manual to learn what the symbol looks like.
  • High pitched squeal when braking. When the friction material on the pads is worn close to the backing plate, you may hear a squealing or squeaking noise as you drive regardless of whether you are applying the brakes or not. That squealing or squeaking noise is designed to make you aware that the brake pads are getting low and need to be inspected. If all of the friction material on the brake pad has been worn away, you will hear grinding and scraping noises when you apply the brakes. Pad replacement is mandatory at this point and the vehicle is unsafe to drive until corrected.
  • Brake pedal pulsation or vehicle vibration. Over time, brake rotors may develop excessive thickness variation (>.001 inches), excessive runout on the wheel hub (> .002 inches), or the brake rotor may warp due to high operating temperatures. If these defects exist, you may notice pulsation in the brake pedal or steering wheel during braking. New pads and rotor resurfacing or replacement will be required if the rotor has any of the above-mentioned deficiencies.
  • Vehicle pulling or wandering on braking. If your car pulls to the right or left during braking, that could be a sign of a sticking brake caliper, misalignment of the suspension, and sometimes tire defects or uneven tire inflation from side-to-side. The mechanic who inspects your vehicle will determine if new brake pads alone will resolve the issue or if other repairs are needed.
  • High mileage on existing pads. Regardless of whether any of the above brake system symptoms occur, every 10,000 miles a mechanic should measure the thickness of the remaining friction material on the brake pads and perform a thorough visual inspection of the braking system.
  • Brake system warning lights and/or maintenance reminder messages. Should your brake system warning light ever illuminates, or a brake system related maintenance reminder message appears in the driver information display, have your vehicle inspected and repaired as soon as possible.

How do mechanics replace brake pads?

Normally, pad replacement requires these steps:

  • Confirm the thickness of the remaining friction material on the brake pads. If the remaining friction material is less than 2 mm in thickness, pad replacement is warranted.
  • Visually inspect the brake rotor surface that contacts the pad (for scoring, pitting, grooves, rust) and measure the brake rotor with precision tools for thickness variation, run-out and warpage.
  • Inspect the caliper, torque plate, pads, and rotors to determine if the caliper is operating freely (i.e., inspect for stuck calipers).
  • Install new pads and any additional recommended components (e.g., rotors, if rotors depart from OEM specifications) only with customer approval of course.
  • Lubricate brake system components, such as caliper sliding pins, and inspect the condition of the brake fluid. Top off brake fluid as required.
  • Perform a basic 50 point safety inspection of your vehicle.
  • Finally, the mechanic will test drive your vehicle to confirm normal operation of the brake system.

Is it safe to drive with a brake pad problem?

Driving a vehicle with a known deficiency in the braking system is unsafe and consequently is not recommended. Worn out brake pads can increase stopping distances and so for your safety, it is always advised that worn out brake pads be replaced promptly. Further driving is not recommended and you should request service at your earliest convenience if any of the following circumstances exist: stopping distances are much greater than what you are accustomed to; the brake pedal is not firm or is low; there is loss of braking power assist; the vehicle pulls severely to one side on braking; or the brake system warning light is on.

If you detect unusual noises, such as squealing or grinding, but stopping distances are close to what you are used to, and the brake pedal is firm, and there are no warning lights, it may be safe to proceed to your destination but schedule service at your earliest convenience. When it comes to the brakes on your vehicle, always err on the side of caution and have a mechanic check your brake pads and braking system at the first indication of a problem.

When replacing brake pads keep in mind:

Brake pads must always be replaced as a set, that is both wheels (driver and passenger side) on an axle, front or rear, must be serviced. If brake pads on only one side of the car were replaced, your car might pull to one side when you apply the brakes. Often, resurfacing or replacement of the brake rotors is necessary and a competent mechanic will always measure for wear and damage to the brake rotors and advise you as to whether rotor replacement or re-surfacing is needed.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(1,293)

Rating Summary
1,238
30
10
7
8
1,238
30
10
7
8

Christopher

12 years of experience
142 reviews
Christopher
12 years of experience
Ford Mustang V6-3.8L - Brake Pads Replacement (Rear) - Charlotte, North Carolina
Absolutely Great!

Marques

20 years of experience
12 reviews
Marques
20 years of experience
Ford Mustang V6-4.0L - Brake Pads Replacement (Front, Rear) - Seattle, Washington
Very professional and knowledgeable mechanic. Answered all of my questions and did a great job on my new brakes and rotors. A+ and 5 stars.

James

16 years of experience
39 reviews
James
16 years of experience
Ford Explorer Sport Trac V6-4.0L - Brake Pads Replacement (Front) - San Antonio, Texas
Nice gentleman.

Eduardo

19 years of experience
549 reviews
Eduardo
19 years of experience
Ford Fiesta L4-1.6L - Brake Pads Replacement (Front) - Houston, Texas
Always very quick and professional

Excellent Rating

(1,293)

Rating Summary
1,238
30
10
7
8
1,238
30
10
7
8
Number of Ford Brake Pad Replacement services completed
14223+
services done by our mechanics
TOTAL NUMBER OF EXPERT Ford MECHANICS
1700+
experts on our platform

Recent articles & questions

A Buyer’s Guide to the 2012 Dodge Ram
While While Chrysler has decided to give Ram its very own division, it seems impossible not to think of the Ram 1500 as a Dodge. After all, you’ll still buy your 2012 Ram at a Dodge dealer, and it remains...
How Long Does a Windshield Washer Reservoir Last?
Most Most people take a clean windshield for granted and neglect to realize just how many parts have to work together to clean a dirty front glass. Making sure that each of the parts that helps to keep the windshield...
How to Buy a Car Using Your Home Equity Line of Credit (HELOC)
Buying a new or used car often means that you must find financing (https://www.yourmechanic.com/article/5-essential-things-to-know-about-car-loans). Most often this is either through the dealership, a bank, or an online lender. While most lenders charge a high interest rate when taking out a...

How do I remove the key fob from the ignition switch?

Removing the key from the ignition switch is very easy. First, if your vehicle has an automatic transmission, make sure that it is in PARK. Then, turn your key fob counter-clockwise to the farthest setting, OFF. Then pull the key...

I have a Code P0601 on the PCM. I replaced the PCM, and now I have a code P0118, code P0123, and code P0193.

Hi there, the short answer to your question is no . A PCM with a P0601 (https://www.yourmechanic.com/article/-p0601-obd-ii-trouble-code-internal-control-module-memory-check-sum-error-by-spencer-clayton) (which is a memory module error in the PCM) cannot reliably retrieve codes for the codes you list (P0118 (https://www.yourmechanic.com/article/p0118-obd-ii-trouble-code-engine-coolant-temperature-ect-sensor-circuit-high-open-problem-by-jay-safford) - coolant temp...

RPMs drop to zero (typically on acceleration). Usually come back up and belt squealing sound is heard; sometimes engine shuts down

Hello. We will be happy to assist you. You most likely have a stuck pulley along the serpentine belt routing. My first guess would be the power steering pump because it is leaking fluid so that is the component I...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com