Ford E-150 Econoline Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(105)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(105)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Ford E-150 Econoline Tie Rod End Replacement is $172 with $58 for parts and $114 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1994 Ford E-150 EconolineL6-4.9LService typeTie Rod End - Front Right Outer ReplacementEstimate$602.82Shop/Dealer Price$686.04 - $854.69
1996 Ford E-150 EconolineV8-5.8LService typeTie Rod End - Rear Left Inner ReplacementEstimate$626.72Shop/Dealer Price$733.98 - $974.60
1996 Ford E-150 EconolineV8-5.0LService typeTie Rod End - Rear Right Outer ReplacementEstimate$530.82Shop/Dealer Price$614.10 - $782.79
1996 Ford E-150 EconolineV8-5.8LService typeTie Rod End - Front Left Outer ReplacementEstimate$533.82Shop/Dealer Price$617.77 - $788.65
1994 Ford E-150 EconolineV8-5.8LService typeTie Rod End - Rear Right Inner ReplacementEstimate$785.22Shop/Dealer Price$932.16 - $1291.70
1983 Ford E-150 EconolineV8-5.8LService typeTie Rod End - Front Left Inner ReplacementEstimate$309.05Shop/Dealer Price$368.46 - $517.40
2001 Ford E-150 EconolineV6-4.2LService typeTie Rod End - Front Right Inner ReplacementEstimate$633.24Shop/Dealer Price$762.83 - $1109.36
1998 Ford E-150 EconolineV8-4.6LService typeTie Rod End - Front Right Inner ReplacementEstimate$633.24Shop/Dealer Price$763.54 - $1110.60
Show example Ford E-150 Econoline Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(105)

Rating Summary
92
4
2
2
5
92
4
2
2
5

Kenneth

10 years of experience
31 reviews
Kenneth
10 years of experience
Ford E-150 Econoline V8-5.0L - Car starts and then dies - Salt Lake City, Utah
Real nice guy. I would love to have him work on my van when I get a quote and parts.

Andrew

11 years of experience
337 reviews
Andrew
11 years of experience
Ford E-150 Econoline V6-4.2L - Car is not starting - Columbia, Maryland
Andrew knew his stuff, arrived on time, and provided a quick and easy synopsis. He also gave several suggestions for the vehicles futures and provided a great quote.

Patrick

32 years of experience
369 reviews
Patrick
32 years of experience
Ford E-150 Econoline V8-5.0L - Inspection / Diagnostics - Las Vegas, Nevada
I don't usually write reviews unless the service/experience is exceptionally good or bad. In this case it was exceptionally good as Pat is everything you want in a mechanic. Friendly, knowledgeable, honest and determined to do a good job. He was able to find the root cause of a pretty complicated issue, explaining everything and helped me resolve the problem. He also insisted on me getting back to him to ensure the problem was fixed as he isn't satisfied unless the job is finished properly. I know who my mechanic will be when I'm in the Las Vegas area.

Alex

16 years of experience
435 reviews
Alex
16 years of experience
Ford E-150 Econoline V8-4.6L - Service Battery/cables - Plano, Texas
Alex was great, on-time, and got the job done quickly. Thanks Alex!

Excellent Rating

(105)

Rating Summary
92
4
2
2
5
92
4
2
2
5
Number of Ford E-150 Econoline services completed
1155+
services done by our mechanics
TOTAL NUMBER OF EXPERT Ford MECHANICS
1700+
experts on our platform

Recent articles & questions

Is it Safe to Drive With a Mattress On Your Roof?
If If you bought a mattress at the local mattress store, you may be wondering how to transport it home. While some stores offer delivery, others do not. Tying a mattress to the roof of your car is an option,...
Should I Get a Smog Technician License?
Getting your smog technician license can help you gain more experience as a mechanic, while also earning some extra cash.

How do I use an iPod with the infotainment system?

You can play an iPod through the infotainment system by connecting it via an AUX cable or a USB cable. Both the AUX and the USB cables connect to the ports in the center console. While an AUX cable will...

How much does it cost to replace a sunroof motor on a 1997 Toyota 4Runner

Hi there - unfortunately, this is not a service YourMechanic offers at this time. Thanks for thinking of us though!

What does abs mean

ABS is the acronym for Anti Lock Braking System. It's a safety feature that uses computer control to prevent individual wheels from locking up under hard braking. A wheel that is sliding will not steer, so ABS fixes the old...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com