Ford Bronco Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(124)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(124)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Ford Bronco Tie Rod End Replacement is $178 with $83 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1986 Ford BroncoL6-4.9LService typeTie Rod End - Front Left Inner ReplacementEstimate$451.99Shop/Dealer Price$542.49 - $786.99
1986 Ford BroncoV8-5.8LService typeTie Rod End - Front Left Outer ReplacementEstimate$347.35Shop/Dealer Price$414.96 - $586.25
1988 Ford BroncoV8-5.8LService typeTie Rod End - Rear Right Outer ReplacementEstimate$347.35Shop/Dealer Price$414.96 - $586.25
1973 Ford BroncoL6-3.3LService typeTie Rod End - Rear Left Inner ReplacementEstimate$336.53Shop/Dealer Price$402.78 - $572.31
1968 Ford BroncoV8-5.0LService typeTie Rod End - Front Right Inner ReplacementEstimate$549.24Shop/Dealer Price$637.18 - $819.74
1975 Ford BroncoV8-5.0LService typeTie Rod End - Front Right Inner ReplacementEstimate$549.24Shop/Dealer Price$637.13 - $819.63
1982 Ford BroncoL6-4.9LService typeTie Rod End - Front Right Inner ReplacementEstimate$651.93Shop/Dealer Price$795.26 - $1196.35
1983 Ford BroncoV8-5.0LService typeTie Rod End - Rear Right Outer ReplacementEstimate$354.35Shop/Dealer Price$422.29 - $593.83
Show example Ford Bronco Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(124)

Rating Summary
110
5
1
3
5
110
5
1
3
5

Mathew

17 years of experience
66 reviews
Mathew
17 years of experience
Ford Bronco V8-5.0L - Car is not starting - New Port Richey, Florida
Very knowledgeable and not intimidated by the age and condition of the vehicle. He was able to diagnose and correct the issue that was keeping the car from starting. Additional needs were identified and recommendations provided.

MICHAEL

33 years of experience
184 reviews
MICHAEL
33 years of experience
Ford Bronco V8-5.0L - Car is not starting - Blue Bell, Pennsylvania
Mike was great - he knew exactly what to do to our car and even explained what the was doing. Friendly and happy to help!

Rick

21 years of experience
44 reviews
Rick
21 years of experience
Ford Bronco V8-5.8L - Car starts and then dies - Manteca, California
Very knowledgeable and friendly. Easy to work with.

Joseph

17 years of experience
94 reviews
Joseph
17 years of experience
Ford Bronco V8-5.8L - Ignition Coil - Johns Island, South Carolina
Grwat

Excellent Rating

(124)

Rating Summary
110
5
1
3
5
110
5
1
3
5
Number of Ford Bronco services completed
1364+
services done by our mechanics
TOTAL NUMBER OF EXPERT Ford MECHANICS
1700+
experts on our platform

Recent articles & questions

How to Clean Your Car With Household Items
Keeping your car clean can be a challenge. Baking soda, vinegar, and dish soap are common household items you can use to wash your car inside and out.
How to Replace an Exhaust Gas Recirculation (EGR) Vacuum Modulator
The EGR vacuum modulator meters the EGR valve in some car systems. Some signs of a failing EGR vacuum modulator include stalling and a rough idle.
Tire Maintenance and Safety: How To Care For Your Tires(DELETED)
Tires need to be maintained just like every other part of your vehicle

What does the Park Assist Off message mean?

The Park Assist Off message can appear in the driver information center (DIC). When the DIC displays this alert, a temporary issue has disabled the park assist system. When the issue is resolved, the alert will go away.

Car won't crank or start.

It sounds like you are experiencing several different issues. If the engine hasn't ran since the transmission fluid was added, I would drain and refill the engine with new oil. The issue with not cranking could be your battery. A...

2007 jeep liberty. Noticed no a/c soon realized power steering loss. Battery light came on. Fluid all over engine bay. Need help

Check to see if the drive belt is intact. If it isn't that would explain the loss of power steering, AC and the battery light. If the belt is intact, then something must be locked up, preventing the other parts...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com