Ford Bronco II Intake Manifold Gaskets Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(26)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(26)

Intake Manifold Gaskets Replacement Service

How much does a Intake Manifold Gaskets Replacement cost?

On average, the cost for a Ford Bronco II Intake Manifold Gaskets Replacement is $559 with $111 for parts and $448 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1990 Ford Bronco IIV6-2.9LService typeIntake Manifold Gaskets ReplacementEstimate$787.46Shop/Dealer Price$871.85 - $1099.08
Show example Ford Bronco II Intake Manifold Gaskets Replacement prices

What is an intake manifold gasket and how does it work?

The intake on an engine may be made up of a lower intake manifold and an upper intake manifold or plenum. The lower intake manifold is a cast aluminum or molded plastic chamber bolted to the cylinder head of the engine. The intake manifold must be tightly sealed to the cylinder head(s) using a gasket in order to prevent air, oil, or engine coolant leaks.

When to consider replacing the intake manifold gasket:

Internal or external leaks. Due to constant temperature expansion and contraction of engine parts or overheating, the gasket’s ability to seal properly can be ruined, resulting in problems such as:

  • Internal or external engine coolant leaks. In some applications, the manifold has cooling passages within. If the manifold seal to the engine fails, coolant can leak externally or even into the engine oil crankcase, where coolant can be noticed in the engine oil.
  • Engine overheating. If the leak at the manifold is a leak of engine coolant, it can lead to engine overheating. However, there are other causes of engine overheating, so a mechanic would have to determine the actual cause.
  • External oil leaks. On some 6 and 8 cylinder engines, the intake manifold sits atop an oil-lubricated area of the engine block. If the manifold gasket has failed, oil can leak from the block to the exterior of the engine.
  • Poor engine operation, lean operation, rough idle. Vacuum air leaks into the manifold due to a defective gasket that will upset the air-fuel ratio. The engine may run poorly.
  • Check engine light. Minor leaks at the intake manifold gasket will not usually cause the check engine light to illuminate. However, as a leak persists, it may grow larger and it possible for the leak to degrade engine performance enough that it will cause a trouble code to set, which will cause the check engine light to illuminate.

How do mechanics replace the intake manifold gasket?

  • Working on a cold engine, the engine cover is removed. If the intake manifold has internal cooling system passageways, the engine coolant is drained below the level of those passageways.
  • The accelerator cable assembly and cruise control cable are removed and set aside. All electrical connections and emission and vacuum lines in the way of the intake are removed. Ignition components, such as the coil, are removed as needed. If the car has an upper plenum, that is removed and set aside.
  • If the fuel rail is bolted to the intake manifold, the supply and return connections to the fuel rail are disconnected.
  • Once all connections to the manifold are clear, the manifold is unbolted and removed from the engine.
  • Aluminum and plastic manifolds are checked with a machinist’s straightedge to ensure the surface flatness does not exceed the original equipment manufacturer’s specification. If the surface of a manifold is not flat, the new gasket will not seal properly. Plastic manifolds are checked for cracks, heat damage, and warpage.
  • Once the manifold is deemed re-usable or replaced as needed, the new gasket is applied, the manifold is put in position and the mounting bolts are torqued with a calibrated torque wrench in the OEM specified sequence. In some applications, RTV sealant must be applied in corners of the mounting surface or specified hard-to-seal spots, per the service manual.
  • All removed components are then re-installed in the reverse of the above steps.
  • Finally, the vehicle is run and checked for leaks, and test driven.

Is it safe to drive with an intake manifold gasket problem?

Yes. The principal concern with a leaking intake manifold gasket is potential damage to the engine, depending on where the leak is. Although the vehicle will generally be safe to drive, you should schedule service as soon as possible to minimize the chances of additional costly damage. If the leak involves coolant, it could lead to engine overheating damage or the coolant could contaminate the engine oil, which can damage the engine bearings. If there is an air leak to the cylinders, it can cause lean operation which could overheat the catalytic converter.

When replacing the intake manifold gasket keep in mind:

  • In engines where coolant flows through the intake manifold, a leaking intake manifold gasket can be either the cause of or result of engine overheating. If you have a leaking intake manifold gasket, and the engine has overheated, the entire engine should be inspected for damage, such as a blown head gasket. The engine cooling system thermostat should be replaced because engine overheating can damage the cooling system thermostat.
  • Some car engine designs are more likely than others to experience leaking intake manifold gaskets due to material and design issues. Your mechanic can inform you if your car represents one of these cases. Many times a re-designed gasket, or altered installation technique and torque values, will be relevant to avoid a recurrence of any leaks. Mechanics will consult Technical Service Bulletins to determine if any unique circumstance exists for your car.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(26)

Rating Summary
23
2
0
0
1
23
2
0
0
1

Ramon

21 years of experience
166 reviews
Ramon
21 years of experience
Ford Bronco II V6-2.9L - Spark Plugs - Tucson, Arizona
GREAT work!

Jonathan

27 years of experience
18 reviews
Jonathan
27 years of experience
Ford Bronco II V6-2.9L - Car is not starting - San Francisco, California

Diego

22 years of experience
564 reviews
Diego
22 years of experience
Ford Bronco II V6-2.9L - Fuel Pump - Glendale, Arizona
Diego went above and beyond. Completely satisfied with the work did and advice he gave.

David

15 years of experience
103 reviews
David
15 years of experience
Ford Bronco II V6-2.9L - Distributor Cap and Rotor Replacement - Cedar Park, Texas
I'd like to rate higher, but I'm still waiting on a different mechanic to come out and fix my issue. Once I get my truck fixed I'd be happy to rate higher.

Excellent Rating

(26)

Rating Summary
23
2
0
0
1
23
2
0
0
1
Number of Ford Bronco II services completed
286+
services done by our mechanics
TOTAL NUMBER OF EXPERT Ford MECHANICS
1800+
experts on our platform

Recent articles & questions

P003A OBD-II Trouble Code: Turbocharger/Supercharger Boost Control "A" Position Exceeded Learning Limit
The P003A trouble code means the Electronic Computer Module (ECM) has detected an issue in the turbocharger or supercharger system.
How to Write a Contract For Selling Your Car
Create a contract and bill of sale to stay protected when selling your used car. Always include the vehicle information, VIN, and odometer reading.
B1917 OBD-II Trouble Code: Air Bag Memory Clear Circuit Failure
B1917 means there the air bag memory clean circuit has failed, likely due to defective wires or connectors.

Window is off track

This is a pretty common problem with broken window regulators. While the window motor is still working the cables driving it have fallen off of the pulley and no longer are able to move the glass itself. I would recommend...

Loud noise coming front front end.

You should have the tire n the left front checked to see if it is wearing incorrect causing the humming noise. The alignment on the front may be out from a loose upper or lower control ball joints or bushings....

Should I buy a new or used air conditioner compressor for my car?

Buying a used air conditioning compressor could lead to more problems. You could easily end up having to do the job twice and a new compressor is not so expensive that I would take that chance. The good news is...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com