Dodge B200 Brake Pad Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(4)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(4)

Brake Pad Replacement Service

How much does a Brake Pad Replacement cost?

On average, the cost for a Dodge B200 Brake Pad Replacement is $155 with $60 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1978 Dodge B200V8-5.9LService typeBrake Pads - Rear ReplacementEstimate$340.80Shop/Dealer Price$392.26 - $506.13
1979 Dodge B200L6-3.7LService typeBrake Pads - Rear ReplacementEstimate$304.80Shop/Dealer Price$356.29 - $470.18
1975 Dodge B200V8-7.2LService typeBrake Pads - Front ReplacementEstimate$260.31Shop/Dealer Price$311.66 - $443.16
1978 Dodge B200L6-3.7LService typeBrake Pads - Rear ReplacementEstimate$304.80Shop/Dealer Price$356.25 - $470.11
1976 Dodge B200V8-6.6LService typeBrake Pads - Front ReplacementEstimate$260.31Shop/Dealer Price$311.67 - $443.19
1979 Dodge B200L6-3.7LService typeBrake Pads - Front ReplacementEstimate$260.31Shop/Dealer Price$311.66 - $443.16
1976 Dodge B200V8-5.2LService typeBrake Pads - Rear ReplacementEstimate$313.80Shop/Dealer Price$365.04 - $478.75
1978 Dodge B200V8-6.6LService typeBrake Pads - Rear ReplacementEstimate$313.80Shop/Dealer Price$365.71 - $479.92
Show example Dodge B200 Brake Pad Replacement prices

What are brake pads and how do they work?

Brake pads consist of friction material that is bonded to a sturdy steel backing plate. When you push on the brake pedal, the friction material on the brake pads is forced against the inner and outer surfaces of the steel brake rotor under tremendous pressure. The resulting friction causes the wheels on your car to slow rapidly allowing for a quick, safe and controlled stop. After thousands of miles, this friction material eventually wears away, and the brake rotor wears away as well, requiring replacement.

Brakes-Service

When to replace brake pads?

Here are several indications that you need new brake pads:

  • Wear indicator on vehicle dashboard. When the friction material on the brake pads is worn to within 2 mm of the pad backing plate, replacement of the pads is necessary. Most newer cars today have electronics built into the brake pad. When the pad is at a point that it needs to be replaced, a symbol will appear on your vehicle dashboard’s instrument cluster. Consult your owner’s manual to learn what the symbol looks like.
  • High pitched squeal when braking. When the friction material on the pads is worn close to the backing plate, you may hear a squealing or squeaking noise as you drive regardless of whether you are applying the brakes or not. That squealing or squeaking noise is designed to make you aware that the brake pads are getting low and need to be inspected. If all of the friction material on the brake pad has been worn away, you will hear grinding and scraping noises when you apply the brakes. Pad replacement is mandatory at this point and the vehicle is unsafe to drive until corrected.
  • Brake pedal pulsation or vehicle vibration. Over time, brake rotors may develop excessive thickness variation (>.001 inches), excessive runout on the wheel hub (> .002 inches), or the brake rotor may warp due to high operating temperatures. If these defects exist, you may notice pulsation in the brake pedal or steering wheel during braking. New pads and rotor resurfacing or replacement will be required if the rotor has any of the above-mentioned deficiencies.
  • Vehicle pulling or wandering on braking. If your car pulls to the right or left during braking, that could be a sign of a sticking brake caliper, misalignment of the suspension, and sometimes tire defects or uneven tire inflation from side-to-side. The mechanic who inspects your vehicle will determine if new brake pads alone will resolve the issue or if other repairs are needed.
  • High mileage on existing pads. Regardless of whether any of the above brake system symptoms occur, every 10,000 miles a mechanic should measure the thickness of the remaining friction material on the brake pads and perform a thorough visual inspection of the braking system.
  • Brake system warning lights and/or maintenance reminder messages. Should your brake system warning light ever illuminates, or a brake system related maintenance reminder message appears in the driver information display, have your vehicle inspected and repaired as soon as possible.

How do mechanics replace brake pads?

Normally, pad replacement requires these steps:

  • Confirm the thickness of the remaining friction material on the brake pads. If the remaining friction material is less than 2 mm in thickness, pad replacement is warranted.
  • Visually inspect the brake rotor surface that contacts the pad (for scoring, pitting, grooves, rust) and measure the brake rotor with precision tools for thickness variation, run-out and warpage.
  • Inspect the caliper, torque plate, pads, and rotors to determine if the caliper is operating freely (i.e., inspect for stuck calipers).
  • Install new pads and any additional recommended components (e.g., rotors, if rotors depart from OEM specifications) only with customer approval of course.
  • Lubricate brake system components, such as caliper sliding pins, and inspect the condition of the brake fluid. Top off brake fluid as required.
  • Perform a basic 50 point safety inspection of your vehicle.
  • Finally, the mechanic will test drive your vehicle to confirm normal operation of the brake system.

Is it safe to drive with a brake pad problem?

Driving a vehicle with a known deficiency in the braking system is unsafe and consequently is not recommended. Worn out brake pads can increase stopping distances and so for your safety, it is always advised that worn out brake pads be replaced promptly. Further driving is not recommended and you should request service at your earliest convenience if any of the following circumstances exist: stopping distances are much greater than what you are accustomed to; the brake pedal is not firm or is low; there is loss of braking power assist; the vehicle pulls severely to one side on braking; or the brake system warning light is on.

If you detect unusual noises, such as squealing or grinding, but stopping distances are close to what you are used to, and the brake pedal is firm, and there are no warning lights, it may be safe to proceed to your destination but schedule service at your earliest convenience. When it comes to the brakes on your vehicle, always err on the side of caution and have a mechanic check your brake pads and braking system at the first indication of a problem.

When replacing brake pads keep in mind:

Brake pads must always be replaced as a set, that is both wheels (driver and passenger side) on an axle, front or rear, must be serviced. If brake pads on only one side of the car were replaced, your car might pull to one side when you apply the brakes. Often, resurfacing or replacement of the brake rotors is necessary and a competent mechanic will always measure for wear and damage to the brake rotors and advise you as to whether rotor replacement or re-surfacing is needed.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Dodge mechanics

Real customer reviews from Dodge owners like you.

Excellent Rating

(4)

Rating Summary
3
1
0
0
0
3
1
0
0
0

Jay

37 years of experience
947 reviews
Jay
37 years of experience
Dodge B200 V8-5.2L - Fuel is leaking from gas tank - Grand Terrace, California
Jay was Awesome was happy you sent him !!!hope he finishes the job when get my part !

Brian

24 years of experience
200 reviews
Brian
24 years of experience
Dodge B200 V8-5.9L - Car is not starting - Hanover, Pennsylvania
Brian worked very methodically to narrow down the problem I had. It was a starting issue. It seems as though the distributor is the culprit, but I won't know if that is the answer until I replace it with a new one. Brian gave me his phone number to inform him of the results of his diagnosis...He is a pleasure to work with.

Napoleon

27 years of experience
147 reviews
Napoleon
27 years of experience
Dodge B200 * - Car is not starting - Redondo Beach, California
Thank you very much. Napoleon showed up on time and did a wonderful job. I hope he is my mechanic next time I call. Thanks again !! :-)

Jason

32 years of experience
507 reviews
Jason
32 years of experience
Dodge B200 V8-5.2L - Brakes, Steering and Suspension Inspection - San Jose, California
Very patient, kind and considerate. Answered all my questions in a simple way that I could understand. I will always request Jason. Even if he is booked for 2 weeks. I will wait for him to become available. He is worth waiting for. Professional, Competent, Expert, Knowledgable, Goes above and beyond, Friendly, Courteous and Timely.

Excellent Rating

(4)

Rating Summary
3
1
0
0
0
3
1
0
0
0
Number of Dodge B200 services completed
44+
services done by our mechanics
TOTAL NUMBER OF EXPERT Dodge MECHANICS
1400+
experts on our platform

Recent articles & questions

P0625 OBD-II Trouble Code: Generator Field/F Terminal Circuit Low
P0625 means there is an issue with the generator field control circuit often due too shorted connectors or a defective CAN bus.
P0907 OBD-II Trouble Code: Gate Select Position Circuit High
P0907 code means there is an issue within the vehicle's transmission gate select position circuit often due too wiring or rarely, the PCM.
P0315 OBD-II Trouble Code: Crankshaft Position System Variation Not Learned
Trouble code P0315 means the crankshaft position system has a fault, often caused by faulty wiring or corroded sensor connector.

no power on car unless the gas is floored

Hello. It is possible that the timing belt (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-timing-belt) and catalytic converter are damaged at the same time. Or for the same reasons. If the belt is ripping up, you should stop driving the vehicle ASAP as if it brakes...

Car won't start

Hi there, thanks for writing in. It's highly unlikely that the computer is damaged, especially with only 48,000 miles on the vehicle. You may have an issue with your key or the ignition system that is causing some electrical gremlins...

Navigation screen system says "program cannot be read" after new car battery was put in.

Hi there. You will need to do a hard reset on the vehicle if your navigation system is factory in design. Disconnect the battery and turn the headlights on. Hold your foot on the brake pedal for 1 minute and...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com