Chrysler Crossfire Water Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(3)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(3)

Water Pump Replacement Service

How much does a Water Pump Replacement cost?

On average, the cost for a Chrysler Crossfire Water Pump Replacement is $581 with $217 for parts and $364 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2005 Chrysler CrossfireV6-3.2LService typeWater Pump ReplacementEstimate$932.52Shop/Dealer Price$1074.26 - $1478.42
2006 Chrysler CrossfireV6-3.2L TurboService typeWater Pump ReplacementEstimate$909.09Shop/Dealer Price$1046.24 - $1446.96
2005 Chrysler CrossfireV6-3.2L TurboService typeWater Pump ReplacementEstimate$813.41Shop/Dealer Price$926.71 - $1255.71
2004 Chrysler CrossfireV6-3.2LService typeWater Pump ReplacementEstimate$909.09Shop/Dealer Price$1046.30 - $1447.07
2006 Chrysler CrossfireV6-3.2LService typeWater Pump ReplacementEstimate$909.09Shop/Dealer Price$1050.14 - $1453.77
2008 Chrysler CrossfireV6-3.2LService typeWater Pump ReplacementEstimate$909.09Shop/Dealer Price$1046.67 - $1447.71
2007 Chrysler CrossfireV6-3.2LService typeWater Pump ReplacementEstimate$909.09Shop/Dealer Price$1046.35 - $1447.14
Show example Chrysler Crossfire Water Pump Replacement prices

What is a water pump and how does it work?

The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley. The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.

When to consider replacing the water pump:

  • Coolant leaks or overheating. The water pump impeller shaft is supported by a bearing. Eventually, the bearing or seal can wear and leak or damage the impeller. Many water pumps have weep holes near the pump bearing. If you see significant leakage from that weep hole, it is time to replace the pump.
  • Bearing roughness or noise. If the water pump shaft does not turn smoothly or the pump is noisy, the bearing is excessively worn. Pump replacement will be necessary.
  • Timing belt replacement. In engines where the water pump is driven by the timing belt, it is a good idea to replace the water pump at the same time the timing belt is replaced. The extensive work explains why it is always recommended to replace the water pump whenever the mechanic already has these components removed for regularly scheduled timing belt replacement.

How do mechanics replace the water pump?

  • The water pump is usually bolted to the front of the engine. The replacement procedure will vary depending on whether the pump is driven by the timing belt, the serpentine belt, or chain.
  • On a cold engine, the engine coolant is drained to a level below the water pump.
  • Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump.
  • The bolts holding the pump to the engine are removed and the pump is pulled out.
  • The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
  • For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air. The engine is then run and brought to normal operating temperature to check for leaks and ensure normal operating temperature.

Is it safe to drive with a water pump problem?

No. Should the water pump only leak a little bit, you can drive the car. However, a small leak could suddenly enlarge or the pump bearing might unexpectedly seize. Either circumstance would likely cause engine overheating. If a defective water pump causes the overheating, it is not safe to drive because of the damage to the engine.

When replacing the water pump keep in mind:

  • It is best to install a new cooling system thermostat when you install a new water pump, especially if the thermostat is old or original.
  • Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement.
  • The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Chrysler mechanics

Real customer reviews from Chrysler owners like you.

Excellent Rating

(3)

Rating Summary
2
1
0
0
0
2
1
0
0
0

Excellent Rating

(3)

Rating Summary
2
1
0
0
0
2
1
0
0
0
Number of Chrysler Crossfire Water Pump Replacement services completed
33+
services done by our mechanics
TOTAL NUMBER OF EXPERT Chrysler MECHANICS
1200+
experts on our platform

Recent articles & questions

P0721 OBD-II Trouble Code: Output Speed Sensor Range/Performance
P0721 code means the transmission control module (TCM) isn't properly converting incoming pulse signals often due too poor, wiring or sensor.
How to Add Brake Fluid to Your Car
Car brake fluid is necessary to keep your car brakes working properly. Check brake fluid condition and top it off if it's low or discolored.
Electric Vehicles vs. Hybrid Cars
If you’re considering a car that requires less gas power, look into the benefits and drawbacks of both EVs and hybrids.

My timing belt broke what should I do? Can I drive my car?

Hello, thank you for writing in. The timing belt is responsible for keeping the camshaft and the crankshaft in sync so the valves will open and close accordingly. With that said, the vehicle is likely not going to run at...

Mercedes Benz Vito 115CDI hot starting problem

Hi there. The glow plugs are designed to help start the engine even when the engine is hot. If the code is on for the glow plugs, check the glow plug relay and timer and see if its energizing as...

can i drop a 454 small block chevy into a 2014 lancer? if so what expertise would be needed

Hi Christopher. Is it possible....certainly. However, the only thing you'd be able to use with the existing Mitsubishi is the body and maybe a few interior parts, as you'd have to install a full frame, rear wheel drive, new engine...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com