Chevrolet Metro Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chevrolet Metro Brake Drum Replacement is $330 with $140 for parts and $190 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1992 Chevrolet MetroL4-1.3L	Service typeBrake Drum Replacement	Estimate$703.78	Shop/Dealer Price$834.73 - $1173.58
1999 Chevrolet MetroL4-1.3L	Service typeBrake Drum Replacement	Estimate$516.94	Shop/Dealer Price$611.85 - $840.23
2000 Chevrolet MetroL3-1.0L	Service typeBrake Drum Replacement	Estimate$469.44	Shop/Dealer Price$559.34 - $783.96
1999 Chevrolet MetroL3-1.0L	Service typeBrake Drum Replacement	Estimate$516.94	Shop/Dealer Price$611.79 - $840.12
2000 Chevrolet MetroL4-1.3L	Service typeBrake Drum Replacement	Estimate$469.44	Shop/Dealer Price$559.37 - $784.02
1998 Chevrolet MetroL4-1.3L	Service typeBrake Drum Replacement	Estimate$516.94	Shop/Dealer Price$611.84 - $840.22
1998 Chevrolet MetroL3-1.0L	Service typeBrake Drum Replacement	Estimate$529.44	Shop/Dealer Price$624.00 - $852.13
2001 Chevrolet MetroL4-1.3L	Service typeBrake Drum Replacement	Estimate$534.40	Shop/Dealer Price$638.51 - $904.71

Show example Chevrolet Metro Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(13)

Rating Summary

13

0

0

0

0

13

0

0

0

0

SEE REVIEWS NEAR ME

Milton

37 years of experience

239 reviews

Milton

37 years of experience

by melany

Chevrolet Metro L4-1.3L - Tune up inspection - North Las Vegas, Nevada

A REAL mechanic, very nice, very helpful, very honest TY Milton :)

Fabrice

20 years of experience

134 reviews

Request Fabrice

Fabrice

20 years of experience

Request Fabrice

by Robert

Chevrolet Metro L3-1.0L - Car Inspection - Orlando, Florida

Fabrice did an excellent job diagnosing a coolant leak (which I originally thought was a water pump leak meaning a timing belt replacement), and went above and beyond when finding and replacing an O-ring which is no longer available even in aftermarket. Fabrice is ASE certified - that should be added to his mechanic profile.

Nicholas

21 years of experience

354 reviews

Request Nicholas

Nicholas

21 years of experience

Request Nicholas

by Marisa

Chevrolet Metro L4-1.3L - Oil Change - Englewood, Colorado

Nick was amazing as always. Had him work on my other vehicle and he did such a great job wouldn't have anyone else look at my other cars. He is fast, knowledgeable, and clean. Other places will try to up sell you and he actually told me what I ACTUALLY needed instead of up selling me. Also told him what another place said I needed and he gave me honest feedback about the actual time frame if it did needed or whether or not it was even really bad. Highly recommend anyone who gives this guy less than 5 stars has no idea what they are doing or is complaining about YouMechanic not Nick.

Stephen

12 years of experience

36 reviews

Request Stephen

Stephen

12 years of experience

Request Stephen

by Catherine

Chevrolet Metro L4-1.3L - Headlight Bulb Replacement (Driver Side Low Beam, Driver Side High Beam) - San Diego, California

Very nice, capable and had the job completed quickly and efficiently.

Excellent Rating

(13)

Rating Summary

13

0

0

0

0

13

0

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

What is a Clean CarFax?

When When purchasing a pre-owned vehicle, you can have greater peace of mind about its reliability when you get a vehicle history report from CarFax (http://www.carfax.com/). Reviewing the information on this report can help you determine whether it is the...

Symptoms of a Bad or Failing Rear Window Transmission

If you hear squealing noises or the window jerks, stops moving halfway, or doesn't move at all, get the rear window transmission inspected.

3 Ways to Increase Your Car Tire Lifespan

Car tires last longer if you drive carefully and keep tires aligned and inflated. Regularly rotate car tires and check for signs of damage.

2007 Honda Odyssey, 102K miles. Started hearing some engine noise when turning steering wheel at low speed couple of weeks ago. En

The noise associated with steering at low speed is not related to the fault causing code P1717 to display. The steering related noise could involve the power steering pump and/or drive belt although there are other possibilities. To pinpoint the...

My serpentine belt has come off(not broken) my 330xi 2001 BMW, first started the car and sounded really rough then smoke came out

You should check each pulley and tensioner or component driven by the belt to see if one of the components are seized that caused the belt to come off. Have a mechanic like one from YourMechanic to come to you...

Brown liquid leaking under passenger side no dash lights

The brown liquid you are seeing sounds like you may have a leaking heater core or radiator (https://www.yourmechanic.com/services/radiator-replacement) that may have some rust inside, which may explain the brown color and steaming. I would suggest having a professional from YourMechanic...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com