BMW 430i xDrive Water Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(101)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(101)

Water Pump Replacement Service

How much does a Water Pump Replacement cost?

On average, the cost for a BMW 430i xDrive Water Pump Replacement is $575 with $337 for parts and $238 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2017 BMW 430i xDriveL4-2.0L TurboService typeWater Pump ReplacementEstimate$938.32Shop/Dealer Price$1113.15 - $1623.85
2018 BMW 430i xDriveL4-2.0L TurboService typeWater Pump ReplacementEstimate$1112.79Shop/Dealer Price$1287.00 - $1797.24
Show example BMW 430i xDrive Water Pump Replacement prices

What is a water pump and how does it work?

The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley. The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.

When to consider replacing the water pump:

  • Coolant leaks or overheating. The water pump impeller shaft is supported by a bearing. Eventually, the bearing or seal can wear and leak or damage the impeller. Many water pumps have weep holes near the pump bearing. If you see significant leakage from that weep hole, it is time to replace the pump.
  • Bearing roughness or noise. If the water pump shaft does not turn smoothly or the pump is noisy, the bearing is excessively worn. Pump replacement will be necessary.
  • Timing belt replacement. In engines where the water pump is driven by the timing belt, it is a good idea to replace the water pump at the same time the timing belt is replaced. The extensive work explains why it is always recommended to replace the water pump whenever the mechanic already has these components removed for regularly scheduled timing belt replacement.

How do mechanics replace the water pump?

  • The water pump is usually bolted to the front of the engine. The replacement procedure will vary depending on whether the pump is driven by the timing belt, the serpentine belt, or chain.
  • On a cold engine, the engine coolant is drained to a level below the water pump.
  • Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump.
  • The bolts holding the pump to the engine are removed and the pump is pulled out.
  • The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
  • For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air. The engine is then run and brought to normal operating temperature to check for leaks and ensure normal operating temperature.

Is it safe to drive with a water pump problem?

No. Should the water pump only leak a little bit, you can drive the car. However, a small leak could suddenly enlarge or the pump bearing might unexpectedly seize. Either circumstance would likely cause engine overheating. If a defective water pump causes the overheating, it is not safe to drive because of the damage to the engine.

When replacing the water pump keep in mind:

  • It is best to install a new cooling system thermostat when you install a new water pump, especially if the thermostat is old or original.
  • Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement.
  • The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(101)

Rating Summary
95
3
1
1
1
95
3
1
1
1

Attila

20 years of experience
1104 reviews
Attila
20 years of experience
BMW 430i xDrive L4-2.0L Turbo - Brake Pads Replacement (Rear) - Secaucus, New Jersey
Great mechanic

Jermaine

25 years of experience
382 reviews
Jermaine
25 years of experience
BMW 328i xDrive L6-3.0L - Water Pump Replacement - Washington, District of Columbia
Jermaine was efficient and knowledgeable.

Eduardo

20 years of experience
570 reviews
Eduardo
20 years of experience
BMW 135i L6-3.0L Turbo - Water Pump - Houston, Texas
Very prompt, courteous and professional. Would highly recommend.

Luther

17 years of experience
57 reviews
Luther
17 years of experience
BMW 330xi L6-3.0L - Water Pump - Austell, Georgia
Well done. Car is running smoothly. No longer overheating.

Excellent Rating

(101)

Rating Summary
95
3
1
1
1
95
3
1
1
1
Number of BMW Water Pump Replacement services completed
1111+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1200+
experts on our platform

Recent articles & questions

P3481 OBD-II Trouble Code: Cylinder 11 Deactivation/Intake Valve Malfunction
P3481 means an issue in engine cylinder 11 caused by cylinder 11 deactivation solenoid connection, restricted oil pressure or fuel pressure issues.
How to Replace a Camshaft Seal
Camshaft seals are round, rubber oil seals between cylinder heads and valve cover gaskets. Worn out cam seals need to be replaced to prevent oil loss.
Top 10 Scenic Drives in Northern California
Exploring northern California is especially exciting because the region is home to an impressively wide variety of terrain, ranging from sandy beaches to tall, rugged mountains. The possibilities for day trips or weekend getaways consequently abound. Whether winding through wine...

What does the StabiliTrak off light mean?

The StabiliTrack off light is located on your instrument panel. When the StabiliTrack system has been turn off, the StabiliTrack off light will illuminate. Tip The StabiliTrack of light will briefly illuminate when the car is turned on. When the...

P1811 code. Is this a major code?

Hi, thanks for writing in. This code occurs when the PCM sees that the transmission takes longer to shift than the given parameters. The PCM uses several parameters, like load and speed, to tell the transmission when it should shift....

P0022

Hi there. The Lucas oil stabilizer should not have caused any issues. The P0019, P0022, P0300, P0305, P0307, and P0308 codes are all related to bank(2). The camshaft position out of sync has, more than likely, led to the misfire...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com