BMW 318ti Car starts and then dies Inspection at your home or office.

Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.

Estimate price near me

Service Location

Customer Ratings

(7)

How A Diagnostic Works

Instantly book a certified mobile mechanic to come to you

Mechanic diagnoses the problem and quotes necessary repairs

Your vehicle is ready to go

Fair, upfront & transparent pricing for all services

Our certified mobile mechanics can come to you now.

Customer Ratings

(7)

Car starts and then dies Inspection Service

How much does a Car starts and then dies Inspection cost?

On average, the cost for a BMW 318ti Car starts and then dies Inspection is $95 with $0 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1996 BMW 318tiL4-1.9LService typeCar starts and then dies InspectionEstimate$114.99Shop/Dealer Price$132.49 - $145.62
1999 BMW 318tiL4-1.9LService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$112.52 - $125.67
1995 BMW 318tiL4-1.8LService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$112.52 - $125.67
1998 BMW 318tiL4-1.9LService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$112.48 - $125.60
1997 BMW 318tiL4-1.9LService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$112.55 - $125.72
Show example BMW 318ti Car starts and then dies Inspection prices

Starting a vehicle only to have it quit immediately after can be confusing and annoying for many drivers especially if their vehicle has not experienced this type of issue before. Typically, a vehicle will start and then quit because of an issue with the fuel or electrical system. It is important to monitor fuel levels as well as warning lights which can signal to the driver that a vehicle may quit unexpectedly.

How this system works:

To start a vehicle, the electrical system, composed of the battery and starter, turns the engine over. Once running, the engine requires a constant flow of gasoline and good spark to keep that fuel igniting. If gasoline is not readily available, or if there is not enough spark, the engine will quit. More modern vehicles with sophisticated computers may affect the way the vehicle runs. These computers help the car run efficiently but can also shut a car down if the fuel/air mixture is not correct. While an older vehicle may be less sophisticated and easier to diagnose, the computers on modern cars can provide more specific information when connected to a code scanner/reader.

Common reasons for this to happen:

  • Mass Airflow Sensor: The mass airflow sensor measures how much air is entering the engine and relays this information to the vehicle’s computer so that the right amount of fuel can be delivered from the fuel injectors. When a sensor begins to fail, the vehicle’s computer may generate an error code to indicate that something has gone wrong. An issue with the mass airflow sensor may manifest itself when a car starts and then stalls soon after starting.

  • Fuel Pump Relay: The fuel pump relay functions much like a fuse for an electric fuel pump. The fuel pump relay engages as the vehicle is started and starts the fuel pump. While the vehicle is running, the fuel pump relay turns off and the fuel pump is powered by the oil pressure sending unit. If the vehicle’s computer is unable to keep the fuel pump relay running throughout the starting process, the vehicle may start and quit immediately after starting.

  • Ignition Coil: Your vehicle’s ignition coil takes the low voltage of the battery and provides the thousands of volts needed to create a spark in the spark plugs. When an ignition coil begins to fail, it may struggle to provide consistent spark to the plugs, causing the engine to stall after starting.

What to expect:

A top-rated mobile mechanic will come to your home or office to determine the reason why the vehicle starts and then dies. The mechanic will then provide a detailed inspection report outlining why the vehicle quit and the cost of any repairs that need to be made.

How it's done:

A mechanic will begin diagnosing your vehicle’s issue by plugging a code reader/scanner into the vehicle’s computer. The mechanic should be able to get more information from your vehicle’s computer on what component has failed. Using this information, the mechanic can begin necessary repairs.

If your vehicle has a bad or failing mass airflow sensor, the mechanic will begin by finding the sensor in the engine bay and checking for any signs of failure. The mechanic should check the wire harness connected to the sensor to ensure that all of wires are properly connected. After removing the sensor, the mechanic should be able to discover the nature of the failure and replace the sensor.

If the mechanic suspects an issue with the fuel pump relay, he or she should check the vehicle’s computer for a problem. If the vehicle’s computer is having difficulty providing consistent power to the fuel pump relay, the computer may need to be reprogrammed or replaced. If the vehicle’s computer is functioning normally, the mechanic may need to replace the fuel pump relay.

If the mechanic suspects that the ignition coil may be faulty, he or she should first disconnect the battery before beginning work. The mechanic should then begin the process of disconnecting wires from the ignition coil and removing it from the engine bay. The mechanic will then install the new ignition coil and ensure that it is connected properly. The mechanic should then reconnect the battery and test the new coil.

With all repairs, the mechanic will ensure the newly installed parts work properly. The mechanic can then turn off and warning lights that may have come on while the vehicle was not running properly.

How important is this service?

If your vehicle is starting but dying soon after starting, you should have it checked out by a mechanic. Issues involving the fuel management and electrical systems will become worse if not dealt with. Diligence and paying attention to warning lights may help prevent further damage to critical engine component and may save money in repairs. A vehicle that quits after starting can be inconvenient and having a mobile mechanic inspect and repair you vehicle will ensure that you and your vehicle are back on the road soon.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(7)

Rating Summary
5
2
0
0
0
5
2
0
0
0

Danny

11 years of experience
269 reviews
Danny
11 years of experience
BMW 318ti L4-1.8L - Engine is making a gurgling sound Inspection - Philadelphia, Pennsylvania
Danny was really great. He even said he wouldn't charge me if he couldn't find what was wrong, since at one point it wasn't clear. But he found the problem and explained everything.

Robert

31 years of experience
641 reviews
Robert
31 years of experience
BMW 318ti L4-1.9L - Oil Change - Los Gatos, California
Great mechanic

Trevor

22 years of experience
185 reviews
Trevor
22 years of experience
BMW 318ti L4-1.9L - Pre-purchase Car Inspection - San Marcos, California
Trevor was honest and very helpful. I highly recommend him.

Casime

12 years of experience
56 reviews
Casime
12 years of experience
BMW 318ti L4-1.9L - Car Starter Repair - Clementon, New Jersey
very efficient and thorough with his work. He had lots of patience while fixing my car which shows professionalism. Satisfied with the work done. Thank you.

Excellent Rating

(7)

Rating Summary
5
2
0
0
0
5
2
0
0
0
Number of BMW 318ti services completed
77+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1100+
experts on our platform

Recent articles & questions

A Buyer’s Guide to the 2012 Nissan LEAF
The The introduction of the LEAF represented the beginning of an age many car experts were skeptical would even happen – true mass production of a 100% electric vehicle. Not only did it happen but the LEAF was grabbed up...
How to Buy Good Quality Ball Joints
Even Even though the name sounds small, the function is big. Ball joints help support your car’s weight by serving as a connection and pivot point between the suspension and your tires. In today’s cars these parts are typically lubricated...
How to Replace a Throttle Return Spring
Replacing a failing throttle return spring is essential to keep driving safely. It requires needle nose pliers and some hand work.

How does the vehicle security system work?

If your car is equipped with a vehicle security system rather than the Nissan Vehicle Immobilizer system, it’s important to know a few things about how it works. When properly armed, the system will flash the car’s lights and honk...

Key stuck in ignition of a 1988 Chevrolet Camaro

If this is an automatic you can try wiggling the shifter while trying to turn the keys, there is a rod that actuates a lock in the lock cylinder unless its in park. If that doesn't help the lock is...

Brakes out hitting hole

Hi there, thanks for writing in about your 2000 Ford E-250. Some master cylinders will let in just a little bit of air when the fluid is splashed around too much in the reservoir, which is likely what has happened to yours....

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com