BMW 230i Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(6,643)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(6,643)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a BMW 230i Brake Drum Replacement is $448 with $305 for parts and $142 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2017 BMW 230iL4-2.0L TurboService typeBrake Drum ReplacementEstimate$783.17Shop/Dealer Price$950.84 - $1420.10
2018 BMW 230iL4-2.0L TurboService typeBrake Drum ReplacementEstimate$772.16Shop/Dealer Price$941.87 - $1412.65
2019 BMW 230iL4-2.0L TurboService typeBrake Drum ReplacementEstimate$772.16Shop/Dealer Price$941.86 - $1412.65
Show example BMW 230i Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(6,643)

Rating Summary
6,192
205
60
44
142
6,192
205
60
44
142

Theodore

16 years of experience
1601 reviews
Theodore
16 years of experience
BMW 335i L6-3.0L Turbo - Car is not starting - Bellevue, Washington
It was great. Even though we couldn't get to the exact cause. Theodore did a great analysis and gave valuable advice on the car condition.

John

27 years of experience
1019 reviews
John
27 years of experience
BMW 750i xDrive V8-4.4L Turbo - Pre-purchase Car Inspection - Houston, Texas
Excellent, simply excellent! Extremely Competent and knowledgeable. Based on his guidance, I was able to make the right decision. Simply Excellent!!!

Patrick

33 years of experience
1419 reviews
Patrick
33 years of experience
BMW 535i L6-3.0L Turbo - Oil Change - Austin, Texas
Great job, sufficent, quick, and on time!

Duane

25 years of experience
512 reviews
Duane
25 years of experience
BMW X5 L6-3.0L - Noise from engine or exhaust - Chula Vista, California
Best in class customer service experience! Duane made an effort to walk me thru every step of the process and provides a detailed about the services performed. He took the service TO THE NEXT LEVEL... He really honored the company's name... I trust that I can now call him "MY MECHANIC"

Excellent Rating

(6,643)

Rating Summary
6,192
205
60
44
142
6,192
205
60
44
142
Number of BMW services completed
73073+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1100+
experts on our platform

Recent articles & questions

How Long Does a Cruise Control Clutch Release Switch Last?
The The cruise control clutch release switch is only located on manual transmission vehicles. These vehicles have a clutch pedal, is depressed. The cruise control works on a circuit system. If the clutch pedal is not pressed in at all,...
Symptoms of a Bad or Failing Automatic Timing Advance Unit
If your car experiences engine knock, sluggish performance, or excessive black smoke, you may need to replace your automatic timing advance unit.
How to Check Your Car Brake Lights
Car brake lights are essential for driving safely. Check the brake lights and brake fuses regularly to keep the brake system working well.

What is the Global Open Windows system?

If your car is equipped with it, the Global Open Windows system lets you operate the driver and passenger front windows and the moon roof with your remote. Here’s what you need to know: The Unlock button on your remote...

Car is overheating and no heat. 2000 Dodge Neon

Hi there - you may have 2 distinct problems at this point. If your engine is still overheating (https://www.yourmechanic.com/question/car-overheating-despite-repairs), the cooling system may not have been bled properly, leaving air pockets in the system, and causing poor heat transfer, no...

can I swap a 96 accord vtec distributor for my 96 civic 1.6 non vtec distributor

Hi there. On the VTEC engine, there are several different electrical connections that would have to be upgraded in order for it to fit correctly. But, for the same year, I believe the motor mounts are in the same location...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com