Audi Q3 Water Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(4)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(4)

Water Pump Replacement Service

How much does a Water Pump Replacement cost?

On average, the cost for a Audi Q3 Water Pump Replacement is $528 with $367 for parts and $161 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2015 Audi Q3L4-2.0L TurboService typeWater Pump ReplacementEstimate$1408.72Shop/Dealer Price$1712.54 - $2454.69
2017 Audi Q3L4-2.0L TurboService typeWater Pump ReplacementEstimate$2182.20Shop/Dealer Price$2668.71 - $4031.33
2016 Audi Q3L4-2.0L TurboService typeWater Pump ReplacementEstimate$1322.72Shop/Dealer Price$1626.66 - $2368.90
2018 Audi Q3L4-2.0L TurboService typeWater Pump ReplacementEstimate$894.56Shop/Dealer Price$1094.82 - $1657.38
Show example Audi Q3 Water Pump Replacement prices

What is a water pump and how does it work?

The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley. The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.

When to consider replacing the water pump:

  • Coolant leaks or overheating. The water pump impeller shaft is supported by a bearing. Eventually, the bearing or seal can wear and leak or damage the impeller. Many water pumps have weep holes near the pump bearing. If you see significant leakage from that weep hole, it is time to replace the pump.
  • Bearing roughness or noise. If the water pump shaft does not turn smoothly or the pump is noisy, the bearing is excessively worn. Pump replacement will be necessary.
  • Timing belt replacement. In engines where the water pump is driven by the timing belt, it is a good idea to replace the water pump at the same time the timing belt is replaced. The extensive work explains why it is always recommended to replace the water pump whenever the mechanic already has these components removed for regularly scheduled timing belt replacement.

How do mechanics replace the water pump?

  • The water pump is usually bolted to the front of the engine. The replacement procedure will vary depending on whether the pump is driven by the timing belt, the serpentine belt, or chain.
  • On a cold engine, the engine coolant is drained to a level below the water pump.
  • Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump.
  • The bolts holding the pump to the engine are removed and the pump is pulled out.
  • The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
  • For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air. The engine is then run and brought to normal operating temperature to check for leaks and ensure normal operating temperature.

Is it safe to drive with a water pump problem?

No. Should the water pump only leak a little bit, you can drive the car. However, a small leak could suddenly enlarge or the pump bearing might unexpectedly seize. Either circumstance would likely cause engine overheating. If a defective water pump causes the overheating, it is not safe to drive because of the damage to the engine.

When replacing the water pump keep in mind:

  • It is best to install a new cooling system thermostat when you install a new water pump, especially if the thermostat is old or original.
  • Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement.
  • The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Audi mechanics

Real customer reviews from Audi owners like you.

Excellent Rating

(4)

Rating Summary
4
0
0
0
0
4
0
0
0
0

Chuck

10 years of experience
347 reviews
Chuck
10 years of experience
Audi Q3 L4-2.0L Turbo - Alternator - Dallas, Texas
As far as I can tell, Chuck did a great job and was friendly throughout the process.

Oscar

16 years of experience
136 reviews
Oscar
16 years of experience
Audi Q3 L4-2.0L Turbo - Car Battery Replacement - Houston, Texas
Kind, knowledgeable, and professional.

Dan

39 years of experience
975 reviews
Dan
39 years of experience
Audi Q3 L4-2.0L Turbo - Spark Plug Replacement - Buford, Georgia
Wonderful guy! Thank you so much for taking care of my four wheel baby.

Raul

5 years of experience
46 reviews
Raul
5 years of experience
Audi Q3 L4-2.0L Turbo - Oil Change - Moreno Valley, California
Raul was on time , polite and works quickly. will use this service again, very convenient.

Excellent Rating

(4)

Rating Summary
4
0
0
0
0
4
0
0
0
0
Number of Audi Q3 services completed
44+
services done by our mechanics
TOTAL NUMBER OF EXPERT Audi MECHANICS
700+
experts on our platform

Recent articles & questions

A Mechanic's Guide to Restoring Classic Cars
Classic car restoration is a way to build your dream car. Before you start you need to set your goals, create a budget, and find the right car parts.
B1985 OBD-II Trouble Code: Seat Switch Lumbar Deflate Circuit Failure
B1985 means there the switch lumbar deflate circuit is bad. This is most likely due to a faulty circuitry in the part.
Industry News for Automotive Techs: October 8-14
50 MPG Chevrolet Cruz Diesel, Mazda's G-Vectoring drive system, Uber and Volvo collaborate on autonomous cars, and Hubb's new reusable oil filter.

Belts making noise.

Hi there. A noise from the belts can be very annoying. If it is a very high pitched noise then you may have an issue with a loose or worn out belt or a bearing failure in one of the...

Windows won't close

Looking at the wiring diagram for your vehicle, I don't see any part of the circuit that would affect both rear windows, without also affecting the front. Because of this, my guess is that you have two failed power window...

I replaced my battery now the starter motor makes a clunking sound and starts after a few tries

Hello there, many faults will cause your 2003 Land Rover Range Rover to take multiple tries to start. It is great you have already replaced the battery as this is a very likely cause in most cases. There are many...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com