Acura Integra Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(150)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(150)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Acura Integra Tie Rod End Replacement is $129 with $34 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1989 Acura IntegraL4-1.6LService typeTie Rod End - Rear Right Outer ReplacementEstimate$194.35Shop/Dealer Price$230.57 - $295.90
1992 Acura IntegraL4-1.8LService typeTie Rod End - Front Right Outer ReplacementEstimate$334.45Shop/Dealer Price$408.74 - $572.43
1994 Acura IntegraL4-1.8LService typeTie Rod End - Rear Left Inner ReplacementEstimate$307.43Shop/Dealer Price$378.07 - $550.55
2001 Acura IntegraL4-1.8LService typeTie Rod End - Rear Left Inner ReplacementEstimate$306.15Shop/Dealer Price$376.43 - $547.92
1990 Acura IntegraL4-1.8LService typeTie Rod End - Front Right Inner ReplacementEstimate$376.05Shop/Dealer Price$460.77 - $655.70
1997 Acura IntegraL4-1.8LService typeTie Rod End - Rear Left Outer ReplacementEstimate$231.17Shop/Dealer Price$282.75 - $398.03
1997 Acura IntegraL4-1.8LService typeTie Rod End - Rear Right Inner ReplacementEstimate$312.43Shop/Dealer Price$382.83 - $555.13
1989 Acura IntegraL4-1.6LService typeTie Rod End - Front Left Inner ReplacementEstimate$255.15Shop/Dealer Price$311.18 - $434.85
Show example Acura Integra Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Acura mechanics

Real customer reviews from Acura owners like you.

Excellent Rating

(150)

Rating Summary
139
8
0
1
2
139
8
0
1
2

Manuel

6 years of experience
3 reviews
Manuel
6 years of experience
Integra 1995 - Car is not starting - Spring Valley, CA
Manuel was polite, professional, and knowledgeable. He was even 10 minutes early which was great. My car was not starting, and I had done some work to the car prior to Manuel coming out. As soon as Manuel turns the key it started. LOL! None the less Manuel wanted to make sure that this was not a fluke start and went through all the necessary points to check and make sure everything was running the way it should be. He also wanted to make sure the vehicle was safe to drive on the road since it was sitting for about 8 months or so. He was very thorough on asking important questions about the vehicles running condition before when it was not working, and also asking what kind of work I had done prior to him coming out. He did not make any unnecessary recommendations either. Manuel was very helpful in answering all my questions as well. I have to say that it was an overall pleasant experience and I am happy to have my vehicle back on the road again, and to have the peace of mind that the vehicle is safe to drive. Thanks Manuel!

Dustin

5 years of experience
37 reviews
Dustin
5 years of experience
Integra 1995 - Idler Pulley - Tigard, OR
Awesome! Braved the elements and provided quick solutions, I’m definitely using him in future repairs.

Andrew

10 years of experience
440 reviews
Andrew
10 years of experience
Integra 1994 - Distributor Rotor and Cap - Vancouver, WA
Andrew was very informative on what was going on with my Acura and what needed to be done as part of it’s maintenance. He was also early on both appointments which was even better!

Andrew

10 years of experience
440 reviews
Andrew
10 years of experience
Integra 1994 - Fuel Filter - Vancouver, WA
Andrew was very informative on what was going on with my Acura and what needed to be done as part of it’s maintenance. He was also early on both appointments which was even better!

Excellent Rating

(150)

Rating Summary
139
8
0
1
2
139
8
0
1
2
Number of Acura Integra services completed
1650+
services done by our mechanics
TOTAL NUMBER OF EXPERT Acura MECHANICS
1000+
experts on our platform

Recent articles & questions

How to Buy a Good Quality Tire Pressure Gauge
Keeping Keeping an eye on your tire pressure is vital. Low tires wear poorly, and they can have a negative effect on your fuel economy. It also makes them more susceptible to damage – a blowout can ruin anyone’s day....
How to Prepare for the Utah Driver’s Written Test
It It is not possible to get a learner’s permit in Utah until you have first taken and passed your driver’s written test. Driving is an important responsibility, and you need to prove to the state that you have the...
How to Check a Car Fuel Pump
Car fuel pumps transfer gas from the fuel tank to the car engine and can be mechanical or electric. Cars low on gas can cause fuel pumps to overheat.

Tips for maintaining my Honda after 100,000 miles?

The best recommendation I can give to any car owner is follow the manufacturer's maintenance schedule. The 100,000-mile service typically includes inspecting and, if necessary, replacing the fluids in your transmission, hydraulic brake system, and cooling system. Engine and cabin...

How to replace the cam shaft sensor.

The camshaft sensor on this engine is mounted on top of the synchronizer in the front center of motor. The noise may be in the housing and not the sensor. The sensor can be removed from the synchronizer housing and...

I have a 2002 toyota camry and my car starts and turns off after about 10 mins after at first it would not crank so i got a new st

Hello, thank you for writing in. There are several reasons why the vehicle may be stalling. You should ALWAYS start by having the vehicle scanned for codes when there is an issue, regardless of a warning light being illuminated. When...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com